▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Spanners, sockets and screwdrivers: choosing the right tool – Garage Basics motor mechanics lesson

Lesson 62 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Meet the basic hand tools of a mechanic – open-ended and ring spanners, sockets and ratchets, and screwdrivers of different tips – and learn why the right size and type matter, with the science of torque.

Time
35 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

This lesson is about recognising tools. Handling household tools with you is fine; any work on a vehicle should be done with a qualified person. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think modern vehicles use more Torx screws than slotted ones?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using a spanner that is "nearly" the right size. Even a small gap lets the spanner slip and round off the nut. Use the exact size.
  • Using a Phillips screwdriver on a Pozidriv screw. They look similar but do not fit each other properly, so the screwdriver cams out and damages the head.
  • Adding a pipe to a spanner to get more force. It can overload and break the tool or fastener and cause injury. Use the proper tool, such as a breaker bar.

Hands-on: With an adult, look at a household toolkit. Sort the spanners and screwdrivers into types, read the sizes stamped on them, and draw the shape of each screwdriver tip. Then test torque with a door: push near the handle and then near the hinge, and feel which needs more force. No work on a vehicle.

What your child will learn

  • I can name the main types of spanner, socket and screwdriver and say what each is best for.
  • I can explain why a tool must be the right size and type for the fastener.
  • I can calculate torque from force and distance.
  • I can convert between inch and millimetre sizes.

Key words

fastener
A nut, bolt or screw that holds parts together.
torque
Turning force: force × distance from the centre of turning. Measured in newton metres (N m).
socket
A short tube with a shaped inside that fits over a nut or bolt head and is turned by a ratchet or other handle.
ratchet
A handle that turns a socket one way and clicks freely back the other way, so the socket need not be lifted off.

The big ideas

Every nut, bolt and screw on a vehicle is designed to be turned by a particular kind and size of tool. Using the wrong one – a spanner that is a little too big, or a screwdriver tip that does not match – can round off the fastener, damage the part and cause the tool to slip, which is a common way for hands to be cut and knuckles skinned.

The basic kit is spanners (open-ended, ring and combination), sockets with ratchets and extensions, and screwdrivers with different tips. Sizes come in metric (millimetres) and, on some older or American vehicles, imperial (AF), measured in fractions of an inch.

This lesson is about recognising tools and understanding why choice matters – not about doing jobs on a vehicle, which should only be done with a qualified person.

Read-through: the teaching steps

  1. Spanners

    • Open-ended spanner – a U-shaped jaw that slides onto a nut from the side. Quick to use, but it grips only two flats, so it can slip on a tight nut.
    • Ring spanner – a closed ring that surrounds the nut and grips all round. Much less likely to slip or round the nut.
    • Combination spanner – open-ended at one end and a ring of the same size at the other.

    The size stamped on a spanner is the distance across the flats of the nut it fits.

  2. Sockets and ratchets

    A socket fits right over a nut or bolt head. A 6-point socket grips the flats of the nut firmly and is least likely to round it off; a 12-point socket fits on at more angles, which helps in tight spaces.

    Sockets are turned by a ratchet, which clicks back without being lifted off, or by a breaker bar for tight fasteners. Extensions reach nuts hidden deep in an engine bay.

  3. Screwdrivers

    The tip must match the screw head exactly:

    • Flat (slotted) – a single slot.
    • Phillips – a cross shape that can push the screwdriver out under high force.
    • Pozidriv – a cross with extra small lines, designed to grip better than Phillips; a Phillips screwdriver does not fit it properly.
    • Torx – a six-pointed star, common on modern vehicles because it grips well.

    A screwdriver is never used as a lever or chisel.

  4. Metric and inch sizes

    Most modern vehicles use metric fasteners, sized in millimetres. Some older and American vehicles use imperial (AF) sizes in fractions of an inch.

    1 inch = 25.4 mm, so 1/2 inch = 12.7 mm. A 13 mm spanner on a 1/2 inch nut is close but not exact – the small gap can be enough to round the nut.

  5. Torque: why length matters

    Torque = force × distance from the centre of turning.

    A longer handle gives more torque for the same push. Pulling 100 N on a spanner 0.2 m long gives 100 × 0.2 = 20 N m. On a 0.4 m breaker bar, the same pull gives 40 N m.

    That is also why extending a spanner with a pipe is dangerous: it can overload the tool and the fastener, and the tool may snap or slip.

  6. Using tools safely

    Good practice includes:

    • the correct size and type, in good condition;
    • pulling a spanner towards you rather than pushing, so a slip does not throw your hand forward;
    • a ring spanner or 6-point socket for tight fasteners;
    • keeping tools clean and stored, not left on the floor (a trip hazard).

    All work on a real vehicle is done with a qualified person.

The lesson, step by step

35 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task11 minNot assessed, self-checked
Worked examples and guided practice7 minMarked by Classfern
Independent practice (three levels)8 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Workshop safety and tools lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.