Measuring: rulers, feeler gauges and calipers – Garage Basics motor mechanics lesson
Lesson 63 of 70 in the Garage Basics course (ages 11–16)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn how mechanics measure accurately – from rulers and tread depth gauges to feeler gauges and vernier calipers – and practise reading a vernier scale to a fraction of a millimetre.
- Time
- 40 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
Everyday objects are ideal for practice. If your child looks at a real vehicle's tyres with a tread gauge, do it together with the car parked, switched off and cold. Every answer is marked straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think some gaps in an engine must be correct to a few hundredths of a millimetre?”
- Later: the homework, then the practice test.
Watch out for
- Reading a scale from an angle. Parallax makes the reading wrong. Look straight at the scale.
- Forgetting to zero a digital caliper. If the jaws do not read zero when closed, every reading is wrong by the same amount.
- Thinking a feeler blade should be forced into a gap. It should slide in with a slight drag. Forcing it gives a wrong reading and bends the blade.
Hands-on: Measure everyday objects three ways: a coin's diameter with a ruler, then with a caliper if your school has one; the thickness of a sheet of paper by measuring 100 sheets and dividing by 100; and the gap under a door using folded paper as a homemade feeler gauge. Record each result with its unit and the resolution of the tool. No vehicle is needed.
What your child will learn
- I can choose a suitable measuring tool for a length, a small gap or a diameter.
- I can explain what a feeler gauge is and how blades can be combined.
- I can read a vernier caliper to 0.02 mm.
- I can convert between thousandths of an inch and millimetres.
Key words
- resolution
- The smallest change a measuring tool can show. A ruler shows 1 mm; a vernier caliper can show 0.02 mm.
- feeler gauge
- A set of thin steel blades, each of a known thickness, used to measure small gaps.
- vernier caliper
- A measuring tool with sliding jaws and two scales that can measure outside sizes, inside sizes and depths to a fraction of a millimetre.
- parallax
- An error caused by reading a scale from an angle instead of straight on.
The big ideas
Vehicles are built to precise sizes. Some gaps and wear limits are smaller than the thickness of a sheet of paper, and the vehicle maker's data gives the figures a technician must check against. Measuring accurately is one of the core skills of a mechanic.
Different jobs need different tools. A steel rule or tape measures lengths to the nearest millimetre. A tread depth gauge measures tyre grooves. A feeler gauge measures small gaps between parts. A vernier or digital caliper measures diameters, thicknesses and depths to a few hundredths of a millimetre, and a micrometer goes finer still.
This lesson is about how the tools work and how to read them. You can practise on everyday objects; measurements on a real vehicle are made by, or with, a qualified person.
Read-through: the teaching steps
Rulers and tapes
A steel rule is marked in millimetres (and often inches). Its resolution is 1 mm, so it is good for lengths but not for fine wear.
To avoid parallax error, read the scale straight on, with your eye level with the mark. Measure from the zero line, not from the worn end of the rule.
Tread depth gauges
A tread depth gauge has a probe that is pushed into a tyre groove while the body rests on the tread. It reads the depth in millimetres.
It connects to the law: for cars the minimum is 1.6 mm across the middle three-quarters of the tread, all the way round.
Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round. Feeler gauges
A feeler gauge is a set of thin steel blades, each stamped with its thickness, for example 0.10 mm or 0.004 in. A blade is slid into a gap: if it slides in with a slight drag, the gap is that thickness.
Blades can be stacked to make other sizes: 0.25 mm + 0.10 mm = 0.35 mm. Feeler gauges are used for gaps such as spark plug gaps, where the vehicle maker's data gives the figure.
The vernier caliper
A vernier caliper has a fixed main scale and a sliding vernier scale. It has outside jaws (for diameters), inside jaws (for holes) and a depth rod.
To read it:
1. Read the main scale at the vernier's zero line: whole millimetres. 2. Find the vernier line that lines up exactly with a main scale line. 3. Multiply that line's number by the resolution (often 0.02 mm) and add it.
Example: main scale 23 mm; vernier line 14 lines up; 14 × 0.02 = 0.28. Reading = 23.28 mm.
Digital calipers show the reading directly, but must still be zeroed with the jaws closed.
Inches and millimetres
Some data, especially in the US, is in thousandths of an inch (written 0.001 in, often called "thou").
1 inch = 25.4 mm, so 0.001 in = 0.0254 mm.
A gap of 0.028 in = 28 × 0.0254 = 0.711 mm.
Care of measuring tools
Measuring tools are precision instruments. They are kept clean, stored in their cases, never dropped or used as levers, and checked against a known size. A caliper is zeroed before use. A bent feeler blade or a dirty caliper gives a wrong reading – and a wrong reading can mean a wrong decision.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Workshop safety and tools lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.