▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Gear ratios: counting teeth – Garage Basics motor mechanics lesson

Lesson 17 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how two gears of different sizes trade speed for turning force, and work out a gear ratio by counting teeth.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

A calculator is fine for this lesson. The key idea is the trade between speed and turning force; the arithmetic is one division or one multiplication each time. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a lorry needs more gears than a small car?”
  4. Later: the homework, then the practice test.

Watch out for

  • Dividing the wrong way round (driving ÷ driven). Say it aloud: 'driven over driving'. A small gear driving a big gear must give a ratio bigger than 1.
  • Thinking a gear can give more speed and more torque at the same time. It is a trade. If the speed goes down 3 times, the torque goes up 3 times, and the other way round.

Hands-on: Cut two card circles, one with a diameter twice the other, and mark a dot on the rim of each. Roll the small circle around the edge of the large one on a table and count how many times it turns to go once round. If you have a bicycle, ask an adult to hold it steady while you count the teeth on the smallest and largest rear sprockets, keeping your fingers well away from the chain.

What your child will learn

  • I can say which gear is the driving gear and which is the driven gear.
  • I can work out a gear ratio from the numbers of teeth.
  • I can use a gear ratio to find the speed of the driven gear.
  • I can explain why a low gear gives more turning force and a high gear gives more speed.

Key words

driving gear
The gear that is turned by the engine or motor. It is also called the input gear.
driven gear
The gear that is turned by the driving gear. It is also called the output gear.
gear ratio
The number of teeth on the driven gear divided by the number of teeth on the driving gear.
torque
Turning force, measured in newton metres (N m).
rpm
Revolutions per minute: how many full turns something makes in one minute.

The big ideas

A gear is a wheel with teeth. When the teeth of two gears mesh, turning one gear turns the other. If the gears are different sizes, they turn at different speeds. That simple fact is what lets a car pull away from rest and also cruise at speed.

The gear ratio compares the two gears. Count the teeth on the driven gear and divide by the teeth on the driving gear. A small gear driving a large gear gives a ratio bigger than 1: the large gear turns more slowly, but with more torque (turning force). A large gear driving a small gear does the opposite: more speed, less torque.

Nothing is gained for free. Leaving aside small losses to friction, what you gain in torque you lose in speed, in the same proportion. A gearbox is a set of gear pairs, so the driver, or the car itself, can choose the best trade for the moment.

Read-through: the teaching steps

  1. Driving and driven

    In a pair of meshing gears, the driving gear is the one being turned by the engine. The driven gear is the one it turns. Two gears that mesh always turn in opposite directions. Find the two gears in the drawing on the lesson page.

    Driving gear10 teethDriven gear30 teethfast
    Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1.
  2. The gear ratio

    Gear ratio = teeth on the driven gear ÷ teeth on the driving gear.

    In the drawing the driven gear has 30 teeth and the driving gear has 10. The ratio is 30 ÷ 10 = 3, written 3:1 and read as 'three to one'. The driving gear must turn 3 times to turn the driven gear once.

  3. Ratio and speed

    Speed of the driven gear = speed of the driving gear ÷ gear ratio.

    If the driving gear turns at 3,000 rpm and the ratio is 3:1, the driven gear turns at 3,000 ÷ 3 = 1,000 rpm.

  4. Ratio and torque

    Torque at the driven gear = torque at the driving gear × gear ratio (leaving friction aside).

    If the driving gear delivers 100 N m and the ratio is 3:1, the driven gear delivers about 100 × 3 = 300 N m. Speed went down by 3 times; torque went up by 3 times.

  5. Low gears and high gears

    First gear in a car has a large ratio, for example about 3.5:1. It gives plenty of torque to get a heavy car moving, but little speed. Top gear has a small ratio, close to 1:1 or even less. It gives little extra torque but lets the car travel fast while the engine turns slowly.

    • Low gear – big ratio, more torque, less speed
    • High gear – small ratio, less torque, more speed
  6. The same idea on a bicycle

    A bicycle uses a chain and toothed sprockets in place of meshing gears, but the idea is the same. Choosing a larger sprocket at the back makes it easier to climb a hill: more turning force at the wheel, and less speed for each turn of the pedals.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Forces, gears and drivetrain lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.