▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Driveshafts and joints – Garage Basics motor mechanics lesson

Lesson 23 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how spinning shafts carry the drive to wheels that steer and bounce, and why their joints are shaped the way they are.

Time
40 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

A calculator helps. The key ideas are that shafts need joints because the wheels move, and that gears multiply torque so the shafts carry much more than the engine makes. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think front-wheel-drive cars need joints that can work at much larger angles than those on rear-wheel-drive cars?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a driveshaft carries the same torque as the engine makes. The gearbox and final drive multiply the torque many times before it reaches the driveshafts.
  • Thinking a split boot is only a cosmetic problem. A split boot lets grease out and dirt in, and the joint soon wears.
  • Thinking a universal joint and a CV joint are the same. A single universal joint makes the speed vary at an angle; a CV joint keeps it steady, even at large angles.

Hands-on: Bend a flexible drinking straw at its joint and twist one end slowly: the other end turns too, even round the bend. Then make a simple universal joint from two pencils, two paper clips bent into forks and a cross cut from card, joined with sticky tape. Turn one pencil and watch the other follow at an angle.

What your child will learn

  • I can explain why drive shafts need joints that bend.
  • I can describe a universal joint and a constant velocity (CV) joint.
  • I can explain what splines and rubber boots do.
  • I can calculate the torque and speed carried by a shaft.

Key words

driveshaft
A shaft that carries the drive from the differential out to a wheel. In the UK the long shaft along the car is called the propeller shaft.
universal joint
A cross-shaped joint (also called a Hooke's joint) that lets two shafts meet at an angle and still turn each other.
constant velocity (CV) joint
A joint with balls running in grooves that passes drive at large angles while keeping the output speed steady through every turn.
splines
Matching ridges and grooves on a shaft and a hub. They pass torque but let the shaft slide in and out a little.
boot
A flexible rubber cover over a joint that keeps the grease in and dirt and water out. It is also called a gaiter.

The big ideas

The differential is fixed to the body of the car, but the wheels move. They bounce up and down over bumps and, at the front, they steer left and right. The shafts that carry the drive to them must therefore bend and change length while they spin and carry a large torque.

Two kinds of joint do this. The universal joint, a cross-shaped joint used for hundreds of years, lets two shafts meet at an angle. It is used on the propeller shaft of rear-wheel-drive cars, where the angles are small. The constant velocity (CV) joint uses balls running in curved grooves. It can work at the large angles needed by a steered wheel and keeps the output turning smoothly. Front-wheel-drive cars have CV joints at both ends of each driveshaft.

Each joint is packed with grease and covered by a rubber boot. Splines let the shaft slide in and out a little as the suspension moves. Inspection and replacement of these parts is work for a trained technician.

Read-through: the teaching steps

  1. Why shafts must bend

    Look at the drawing on the lesson page. The engine, gearbox and differential are bolted to the car body. The wheels are on the suspension, which moves up and down, and the front wheels steer. A straight solid bar could not reach a wheel that keeps moving, so the shafts have joints.

    EngineClutchGearboxPropeller shaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  2. The universal joint

    A universal joint has two forked ends joined by a cross with four arms on bearings. It lets the two shafts meet at an angle. One weakness: at an angle, a single universal joint makes the output speed up and slow down slightly twice in every turn. Using two joints lined up correctly cancels this out, which is why a propeller shaft has one at each end.

  3. The CV joint

    A constant velocity joint has a set of steel balls held in a cage, running in curved grooves in an inner and an outer part. The balls always sit on the line halfway between the two shafts, so the output turns at exactly the same speed as the input, even at the large angle of a fully steered front wheel.

  4. Splines and plunging joints

    When the suspension moves, the distance from the differential to the wheel changes slightly. Splines, or a sliding (plunging) CV joint at the inner end, let the shaft change length while still passing torque.

  5. Boots keep the grease in

    Each CV joint is filled with grease and sealed by a rubber boot with folds so it can bend. If a boot splits, grease escapes and grit gets in, and the joint wears. A worn outer CV joint often makes a clicking noise on full lock. Checking boots is part of a technician's inspection.

  6. How much torque?

    The driveshafts carry far more torque than the engine makes, because the gearbox and final drive multiply it:

    torque at the differential = engine torque × gear ratio × final drive ratio

    An open differential shares this equally, so each driveshaft carries half.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Forces, gears and drivetrain lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.