▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Wing design: planform, washout, stall strips and small vortex vanes – Private Pilot Theory aviation lesson

Lesson 132 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Why are wings rectangular, tapered, elliptical or swept – and why are some twisted or fitted with little strips and vanes? Learn how designers make wings stall gently.

Time
40 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It is explanation for understanding, not training. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why is gentle, predictable stall behaviour important for a training aeroplane?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking tips should stall first. Root-first keeps the ailerons working.
  • Calling vortex vanes by a banned name. Classfern says 'small vortex vanes'.
  • Thinking washout means washing the wing. It is a built-in twist.

Hands-on: Draw four wing planforms – rectangular, tapered, elliptical, swept – and shade where each tends to stall first, using this lesson. Measure span and chord on a paper model and work out its aspect ratio.

What you will learn

  • I can describe common wing planforms and how they stall.
  • I can explain why designers want the wing root to stall first.
  • I can explain how wing twist (washout) and stall strips work.
  • I can explain what small vortex vanes do.

Key words

planform
The shape of the wing seen from above.
aspect ratio
How long and narrow the wing is: span compared with chord.
washout
Twist that gives the wingtip a smaller angle of attack than the root.
stall strip
A small sharp strip on the leading edge near the root that makes that part stall first.
small vortex vanes
Tiny blades on the wing that stir high-energy air into the boundary layer to keep the flow attached.

The big ideas

The planform is the wing's shape seen from above. The FAA Pilot's Handbook (chapter 5) explains that a rectangular wing tends to stall first at the root and gives adequate stall warning, which is why it suits low-cost, low-speed aeroplanes. An elliptical wing is ideal for low induced drag but gives little advance warning of a complete stall. Tapered wings save weight and add stiffness, and the handbook warns that the tendency for tip stall is greatest when sweep and taper are combined.

Designers want the root to stall first, because the ailerons are near the tips: if the root stalls first, the ailerons keep working and the wing warns the pilot with buffet. Two tools help. Wing twist (washout) gives the root a higher angle of attack than the tip, so the root reaches the critical angle first. Stall strips on the first 20–25 % of the leading edge near the root make the flow break away there first.

The handbook also describes small aerofoils set at a steep angle to the airflow – called small vortex vanes on Classfern – which mix high-energy air into the boundary layer and help keep the flow attached. Aspect ratio, the span compared with the chord, also matters: long, narrow wings have less induced drag.

Read-through: the teaching steps

  1. Rectangular

    Root stalls first; good stall warning; cheap and simple for slow aeroplanes.

  2. Elliptical and tapered

    Elliptical: lowest induced drag but little stall warning. Tapered: lighter and stiffer; sweep plus taper → tip-stall tendency.

  3. Why root first?

    Ailerons sit near the tips. Root-first stalling keeps the ailerons working and gives buffet as a warning.

  4. Washout (twist)

    The wing is twisted so the root meets the air at a higher AOA than the tip – the root stalls first.

  5. Stall strips

    Small sharp strips on the first 20–25 % of the leading edge near the root trip the airflow there first.

  6. Small vortex vanes and aspect ratio

    Vanes mix high-energy air into the boundary layer. Aspect ratio = span ÷ chord; higher means less induced drag.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Principles of Flight lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.