▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Flaps and slats: effect on lift and drag – Private Pilot Theory aviation lesson

Lesson 131 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Flaps and slats let a wing make more lift at low speed. Compare plain, split, slotted and Fowler flaps, and leading-edge slots and slats.

Time
40 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It is explanation for understanding, not training. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might an airliner use different flap settings for take-off and for landing?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking flaps only add lift. They add drag too – a lot at full extension.
  • Thinking slats make the wing stall at a lower angle. Slats and slots delay separation to a higher AOA.
  • Mixing up spoilers and flaps. Spoilers reduce lift and add drag.

Hands-on: Make a paper wing and tape a narrow strip of card along its trailing edge as a 'flap'. Hold it in front of a fan with the flap up, then bent down. Feel the extra lift – and the extra push backwards.

What you will learn

  • I can explain why aircraft have flaps and slats.
  • I can describe plain, split, slotted and Fowler flaps.
  • I can explain how slots and slats delay the stall.
  • I can explain why flaps add drag as well as lift.

Key words

flap
A hinged or sliding surface on the trailing edge that increases lift (and drag).
Fowler flap
A flap that slides back on tracks, adding wing area as well as camber.
slat
A movable leading-edge surface that opens a slot to keep the airflow attached at high angles of attack.
CL-MAX
The maximum lift coefficient a wing can reach.
high-lift device
Any flap, slot, slat or cuff that raises a wing's maximum lift.

The big ideas

Wings are designed to be efficient in cruise, but take-off and landing need lots of lift at low speed. High-lift devices change the wing for that job. The FAA Pilot's Handbook (chapter 6) describes the trailing-edge flaps. A plain flap increases camber and lift substantially but adds a large amount of drag and a nose-down pitching moment. A split flap gives slightly more lift than a plain flap but more drag. A slotted flap – the handbook calls it the most popular type – increases the maximum lift coefficient significantly: a duct lets high-energy air from below flow over the flap's upper surface, delaying separation. A Fowler flap slides aft on tracks, increasing both wing area and camber; it gives a large increase in lift early in its travel, while drag rises most near full extension.

At the leading edge, fixed slots and movable slats direct air over the upper surface to delay separation at high angles of attack; leading-edge flaps and cuffs also raise maximum lift. Spoilers do the opposite – they reduce lift and increase drag.

The result is a lower stall speed, so slower take-offs and landings – at the price of extra drag. This is explained for understanding only.

Read-through: the teaching steps

  1. Why high-lift devices?

    Take-off and landing need lift at low speed. Raising CL-MAX lowers the stall speed.

  2. Plain and split flaps

    Plain: more camber, lift up, large drag, nose-down moment. Split: a little more lift than plain, more drag.

    Aileron (roll)Aileron (roll)Elevator (pitch)Rudder on fin (yaw)
    Ailerons roll the aircraft, the elevator pitches it and the rudder yaws it.
  3. Slotted flaps

    A slot lets high-energy air from below flow over the flap, keeping the flow attached – a big rise in maximum lift.

  4. Fowler flaps

    Slide back then down: more area and camber. Big lift gain early; most drag near full extension.

  5. Leading-edge devices

    Fixed slots, movable slats, leading-edge flaps and cuffs keep air attached at high AOA, lowering the stall speed.

  6. The trade-off

    More lift at low speed, but more drag. Spoilers are the reverse: less lift, more drag.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Principles of Flight lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.