▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Chains, belts and shafts: motorcycle final drive – Vehicles and Technology motor mechanics lesson

Lesson 16 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Compare chain, belt and shaft final drives, work out final-drive ratios from sprocket teeth, and find out why chains wear and need care.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

A bicycle is a safe way to see a chain drive; keep fingers clear of the chain and sprockets while the pedals are turned. Motorcycles should be looked at only when parked, switched off and cold. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If you were designing a motorcycle for riding round the world, which final drive would you choose, and what would you give up?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a chain stretches like elastic. The length grows because pins and bushes wear; the side plates themselves do not stretch.
  • Thinking a bigger front sprocket gives faster acceleration. A bigger front sprocket lowers the ratio, which gives calmer, slower acceleration and lower revs when cruising.
  • Thinking a chain should be as tight as possible. A chain needs slack because the swinging arm moves; a chain set too tight can be damaged or damage the transmission bearings.

Hands-on: With an adult, look at the chain and sprockets on a bicycle turned upside down on a soft mat. Count the teeth on the front chainring and the rear sprocket and work out the ratio. Keep fingers well away from the chain while anyone turns the pedals. If you see a motorcycle, look only while it is parked, switched off and cold.

What you will learn

  • I can name the three kinds of motorcycle final drive.
  • I can calculate a final-drive ratio from the numbers of teeth.
  • I can explain how changing a sprocket changes acceleration and top-speed gearing.
  • I can compare the strengths and weaknesses of chain, belt and shaft drive.
  • I can explain why a moving chain is dangerous and why wheel alignment matters.

Key words

sprocket
A toothed wheel that a chain runs on. The small one is at the transmission; the large one is on the rear wheel.
final-drive ratio
Rear sprocket teeth ÷ front sprocket teeth: how many turns the transmission output makes for one turn of the rear wheel.
chain slack
The small amount of up-and-down free movement a chain needs to run properly as the suspension moves.
toothed belt
A reinforced rubber belt with teeth, running on toothed pulleys, used instead of a chain.
shaft drive
A spinning shaft with bevel gears at the ends, carrying drive to the rear wheel in a sealed housing.
wheel alignment
Whether the rear wheel lines up exactly with the front wheel.

The big ideas

Every motorcycle needs a way to carry the turning force from the transmission output to the rear wheel. This is the final drive, and there are three ways of doing it: a roller chain on sprockets, a toothed belt on pulleys, or a shaft with gears at each end.

Each has strengths. Chains are light, efficient and let the gearing be changed easily, but they need regular cleaning, lubrication and adjustment. Belts are quiet and clean and need no oil. Shafts are sealed and long-lasting but heavier, and they can make the rear of the bike rise or squat under power.

The final drive also sets a fixed gear ratio of its own. This lesson explains how, and why a technician looks closely at chain wear and wheel alignment. This is explanation for understanding: a moving chain can trap fingers, so final-drive work is for trained technicians.

Read-through: the teaching steps

  1. Chain and sprockets

    A roller chain links a small front sprocket on the transmission output to a large rear sprocket bolted to the rear wheel. Chains are light and very efficient, and riders can change the gearing simply by fitting a sprocket with a different number of teeth. The gear-pair drawing on the lesson page shows the same idea with gears.

    Driving gear10 teethDriven gear30 teethfast
    Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1.
  2. Working out the ratio

    final-drive ratio = rear sprocket teeth ÷ front sprocket teeth

    With 15 teeth at the front and 45 at the back, the ratio is 45 ÷ 15 = 3.0:1. The transmission output turns three times for each turn of the rear wheel, and the turning force at the wheel is about three times bigger (minus small friction losses).

  3. Changing the gearing

    • Fewer teeth at the front or more at the rear: a higher ratio number – quicker acceleration, more engine revs at a given speed, lower top-speed gearing
    • More teeth at the front or fewer at the rear: a lower ratio number – calmer cruising, slower acceleration

    One tooth on the small front sprocket makes a bigger difference than one tooth on the large rear sprocket.

  4. Why chains wear

    Each link turns on a pin inside a bush and roller. As these wear, the chain gets longer – people call it "stretch", though the metal is not really stretching. A worn chain rides higher on the sprocket teeth and wears them into a hooked shape, so chains and sprockets are usually replaced together. A technician also checks the chain slack, because the swinging arm moves and a chain that is too tight or too loose is dangerous.

  5. Belt and shaft drive

    A toothed belt is quiet, clean and needs no oil, but it is wider and cannot easily be re-geared. A shaft runs in a sealed housing with bevel gears at each end; it lasts a long time with little attention and suits touring bikes, but it is heavier and the spinning shaft and gears waste a little more energy.

  6. Alignment and safety

    The rear wheel must line up with the front wheel. If one side of a chain adjuster is set differently from the other, the rear wheel points slightly sideways and the bike will not track straight. A running chain can drag in fingers or clothing, so a chain guard covers it. Final-drive work is done by a trained technician with the engine off.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Motorcycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

About this lesson

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.