▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Torque: settings, sequences and angle tightening – Motor Vehicle Theory motor mechanics lesson

Lesson 14 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Understand what torque does to a bolt, why manufacturers give tightening sequences and stages, how angle tightening works, and how to convert N·m and lbf·ft.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains the science of tightening using example numbers for practice. Real torque values always come from the manufacturer; the activity is drawing on paper. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think many modern engines use torque-angle tightening rather than torque alone?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking torque measures the clamping force directly. Torque is indirect; friction can change the clamping force a lot.
  • Thinking tighter is always safer. Over-tightening can yield the bolt or strip the thread; follow the specification.
  • Thinking order does not matter if every bolt reaches the right torque. Sequence and stages decide whether the part sits flat and the gasket seals evenly.

Hands-on: Draw a cylinder head outline on paper with ten bolt holes in two rows of five. Number them in a spiral starting from the center and working outwards, alternating sides, as a typical sequence might do. Then draw a protractor angle of 90° and 180° and write how far a 1.5 mm pitch thread advances for each.

What you will learn

  • I can explain how tightening torque produces bolt stretch and clamping force.
  • I can explain why friction affects the clamping force for a given torque.
  • I can explain the purpose of tightening sequences and stages.
  • I can describe angle tightening and calculate thread travel for a given angle.
  • I can convert torque between N·m and lbf·ft.

Key words

torque
Turning effect: force × perpendicular distance, in newton-meters (N·m) or pound-force feet (lbf·ft).
clamping force
The force with which a tightened fastener holds parts together.
preload
The tension in a bolt after tightening, which creates the clamping force.
tightening sequence
The order in which a group of fasteners is tightened, set by the manufacturer.
angle tightening
Tightening to a seating torque and then turning a further specified angle.

The big ideas

A bolt works like a very stiff spring. When it is tightened, it stretches a tiny amount, and that stretch pulls the joint together with a clamping force. Too little and the joint can loosen or leak; too much and the bolt or thread can fail. Torque is the practical way to control this – but most of the torque is used up overcoming friction, so manufacturers specify exactly how each joint must be tightened.

This lesson explains the science behind torque settings, sequences and angle tightening, and how to convert between units. The values used are example numbers for practice only: real torque figures, sequences and angles always come from the manufacturer's data, and safety-critical joints are worked on only by trained technicians.

Read-through: the teaching steps

  1. What tightening does

    As a nut turns, the thread acts like a ramp, pulling the bolt and stretching it. The stretch (preload) is what clamps the parts. Correct preload keeps the joint tight under vibration and load. Too little and parts can move; too much and the bolt yields or the thread strips.

  2. Where the torque goes

    Typically most of the applied torque is used overcoming friction – in the threads and under the head or nut – and only a small part stretches the bolt. That is why manufacturers say whether threads are to be clean and dry or oiled: changing the friction changes the preload you get for the same torque.

  3. Units and conversions

    • SI unit: newton-meter (N·m).
    • Imperial unit: pound-force foot (lbf·ft), often written ft·lb.
    • 1 lbf·ft = 1.356 N·m.

    To convert lbf·ft to N·m multiply by 1.356; to convert N·m to lbf·ft divide by 1.356.

  4. Sequences and stages

    Components with many fasteners – cylinder heads, wheels, covers – must be pulled down evenly. Manufacturers give a sequence (often a spiral from the center outwards, or a criss-cross pattern) and stages (for example a low torque on all bolts, then a higher torque on all, then a final step). This prevents distortion and uneven gasket compression.

  5. Angle tightening

    Many modern joints use torque-angle tightening: a modest seating torque, then a further turn by a set angle (for example 90°). Because the angle stage depends far less on friction, it gives a more consistent stretch. It is often used with torque-to-yield bolts, which are usually replaced rather than reused.

    Thread travel = pitch × fraction of a turn.

  6. Tools and checks

    Technicians use calibrated torque wrenches and angle gauges, follow the manufacturer's data exactly, and record critical torques where required. Wheel fastenings, brakes, steering and suspension joints are safety-critical; they are tightened only by trained technicians.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Tools and measurement lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

About this lesson

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.