▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Torque converters – Motor Vehicle Theory motor mechanics lesson

Lesson 57 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how a torque converter uses moving fluid to pass drive from the engine, how its stator multiplies torque, and why a lock-up clutch saves fuel.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains how a torque converter works, with ratio, efficiency and power calculations. It is theory only; automatic transmission work is for trained technicians. Torque ratios quoted are typical values. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “A torque converter makes an automatic car easy to drive but wastes some energy. Was it worth it? What has changed since lock-up clutches arrived?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the stator turns all the time with the turbine. The stator is held still for torque multiplication and freewheels only near the coupling point.
  • Thinking a torque converter creates energy because it multiplies torque. Turbine speed is lower, so power out is always less than power in.
  • Thinking the converter changes gear. Gear ratios come from the gear sets after the converter.

Hands-on: Put two desk fans (or one fan and a pinwheel) face to face, about 20 cm apart, with an adult. Switch one on and watch the other start to turn with no contact: that is a fluid coupling using air. Notice it never turns quite as fast. Then draw the impeller, turbine and stator and add arrows for the fluid flow at stall and at the coupling point. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.

What you will learn

  • I can name the impeller, turbine and stator and explain what each does.
  • I can explain torque multiplication, stall and the coupling point.
  • I can calculate torque ratio, speed ratio, slip and efficiency.
  • I can explain why converters need lock-up clutches and fluid cooling.

Key words

impeller
The converter's pump, part of the housing turned by the engine. It throws fluid at the turbine.
turbine
The bladed wheel driven by the fluid; it turns the transmission input shaft.
stator
A bladed wheel on a one-way clutch that redirects fluid back into the impeller to multiply torque.
stall
The condition with the turbine held still and the engine driving the impeller; torque multiplication is greatest here.
lock-up clutch
A clutch inside the converter that locks the turbine to the housing to stop slip.

The big ideas

A conventional automatic transmission has no clutch pedal. Instead, a torque converter sits between the engine and the gear sets. It lets the engine idle while the car stands still, takes up drive smoothly when the driver accelerates, and even multiplies torque when moving off.

It does this with fluid. One bladed wheel driven by the engine throws transmission fluid at a second bladed wheel connected to the transmission. A third wheel, the stator, turns the returning fluid so that it helps the first wheel. The price is slip, which turns some energy into heat, so modern converters add a lock-up clutch.

This is explanation for understanding, not a repair guide. Automatic transmissions are serviced by trained technicians; their fluid can be very hot.

Read-through: the teaching steps

  1. Three wheels in a doughnut

    The converter is a sealed, fluid-filled housing bolted to the engine's flexplate.

    • Impeller (pump): part of the housing; turns at engine speed.
    • Turbine: splined to the transmission input shaft.
    • Stator: between them, on a one-way clutch fixed to a stationary shaft.
    EngineClutchTrans.DriveshaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  2. How the fluid carries drive

    The spinning impeller flings fluid outwards and forward into the turbine. The fluid pushes the turbine blades, gives up energy, flows inwards and returns toward the impeller. The faster the engine turns, the harder the fluid pushes.

  3. Torque multiplication

    When the turbine turns much slower than the impeller, fluid leaves it heading against the impeller's rotation. The stator, held by its one-way clutch, turns that flow so it strikes the impeller helpfully. The result: turbine torque can be greater than engine torque. Torque ratio = turbine torque ÷ impeller torque, typically about 2:1 at stall for car converters.

  4. Stall and the coupling point

    • Stall: turbine held still (car braked in gear) with the engine at full power. Torque ratio is highest, efficiency is zero (no output speed), and heat builds fast.
    • As the turbine speeds up, torque ratio falls.
    • Coupling point: torque ratio reaches about 1. Fluid now hits the back of the stator blades, the one-way clutch freewheels, and the converter acts as a plain fluid coupling.
  5. Slip, efficiency and heat

    Speed ratio = turbine speed ÷ impeller speed. Efficiency = torque ratio × speed ratio.

    Even at the coupling point the turbine turns slightly slower than the impeller. Lost power becomes heat in the fluid, which is why automatics have fluid coolers. Power can be found from P = 2π × N × T ÷ 60 (N in rpm, T in N m, P in watts).

  6. The lock-up clutch

    At cruising speeds the control unit applies a friction clutch inside the converter that locks the turbine to the housing. Slip falls to zero, fuel use falls and less heat is made. The fueleconomy.gov transmission page notes that conventional automatics lose more energy than manual transmissions; lock-up is one way designers close that gap.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.