▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

The multimeter: volts, amps and ohms – Motor Vehicle Theory motor mechanics lesson

Lesson 19 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Learn how a multimeter measures volts, amps and ohms, how it is connected for each, and how Ohm's law helps a technician interpret readings on a 12-volt system.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains multimeter theory. Practice is on a single AA cell and a school circuit kit with a teacher; nobody but a trained technician measures a vehicle's high-voltage system. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a connection that reads well on an ohmmeter still fail a voltage drop test?”
  4. Later: the homework, then the practice test.

Watch out for

  • Measuring current with the meter across the supply. Current is measured in series; across a supply the amps range acts almost like a short circuit.
  • Measuring resistance on a live circuit. Switch off and isolate the component first.
  • Thinking a tiny resistance cannot matter. At high currents, even a small resistance causes a large voltage loss and heat.

Hands-on: With a teacher, use a school multimeter on a single AA cell: measure its voltage (in parallel), then build a simple circuit with the cell, a small bulb or LED kit and wires, and measure the current in series. Use Ohm's law to calculate the bulb's resistance. Never connect a meter to mains sockets or any vehicle system.

What you will learn

  • I can explain voltage, current and resistance and their units.
  • I can state how a meter is connected to measure voltage, current and resistance.
  • I can use Ohm's law and P = V × I.
  • I can explain what a voltage drop reading shows.
  • I can explain why the high-voltage system is for trained technicians only.

Key words

voltage (V)
The electrical push between two points, measured in volts.
current (I)
The rate of flow of electric charge, measured in amps (A).
resistance (R)
Opposition to current, measured in ohms (Ω).
Ohm's law
V = I × R.
voltage drop
The voltage lost across part of a circuit, such as a cable or connection, because of its resistance.

The big ideas

The multimeter is the technician's most-used electrical tool. On the vehicle's 12-volt system it can show whether a supply is present, whether a wire is broken, whether a connection is corroded and how much current a circuit draws.

Three quantities matter: voltage (the push), current (the flow) and resistance (the opposition). Ohm's law links them: V = I × R. The way the meter is connected depends on what it measures – across a component for volts, in series for amps, and on a dead circuit for ohms.

This lesson explains the theory. A meter can safely be practiced on a flashlight cell with a teacher. The high-voltage system of an electric or hybrid vehicle – up to 650 V DC, according to British safety guidance from HSE – is only ever measured by trained technicians with suitably rated equipment.

Read-through: the teaching steps

  1. Volts, amps and ohms

    • Voltage – the push that drives charge, in volts (V).
    • Current – the flow of charge, in amps (A).
    • Resistance – opposition to the flow, in ohms (Ω).

    Ohm's law: V = I × R, so I = V ÷ R and R = V ÷ I. Power: P = V × I. See a simple circuit in the drawing on the lesson page.

    +12 VBatteryFuseSwitchLampReturn through the body (ground)
    A simple lighting circuit. On a car the metal body is the return path (ground).
  2. Measuring voltage

    Set the meter to DC volts and put the probes across the component or between a point and the vehicle body, which is the return path. The meter has very high resistance, so it takes almost no current and does not disturb the circuit. A healthy 12 V lead-acid battery at rest typically reads a little over 12 V.

  3. Measuring current

    Set the meter to amps and move the red lead to the amps socket. The circuit must be broken and the meter put in series, so all the current flows through it. Connecting a meter set to amps across a supply can blow its fuse. Many technicians use a clamp meter instead, which measures current from the magnetic field around a wire.

  4. Measuring resistance and continuity

    Resistance is measured with the circuit switched off and the component isolated, because the meter supplies its own small current. Continuity mode beeps when there is a complete, low-resistance path – useful for finding broken wires.

  5. Voltage drop testing

    A cable or connection should carry current with very little voltage lost along it. Measuring the voltage across a connection while the circuit is working shows its resistance under load. A noticeable voltage drop across a ground strap or terminal points to corrosion or a loose joint – a fault an ohmmeter on a dead circuit might miss.

  6. Meter safety and high voltage

    Meters are rated for the voltages they can safely measure, and leads are checked for damage. On a 12 V system the main risks are short circuits and blown fuses. Electric and hybrid vehicles are different: HSE says contact above 110 V DC can be fatal even when dry. Their high-voltage systems are measured only by trained technicians with suitably rated meters, after isolation and proving dead.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Tools and measurement lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

About this lesson

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.