Switches and relays – Motor Vehicle Theory motor mechanics lesson
Lesson 94 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how switches control circuits, why a relay lets a small switch control a large current, and how to read the numbered terminals on a standard relay.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
The lesson uses Ohm's law and simple ratios. It explains the theory of switching; practical circuit work belongs in a supervised college workshop. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Electronic switching can detect a short circuit and report it, but an old relay cannot. Which would you rather diagnose, and why?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the dashboard switch carries the headlamp current when there is a relay. The switch only carries the small coil current. The relay's contacts carry the load current.
- Thinking relay terminal 87a is just a spare. On a changeover relay, 87a is connected to 30 when the coil is off. Some circuits use it on purpose.
- Thinking a switch on the ground side cannot turn a load off. Breaking the circuit anywhere stops the current. A ground-side switch turns the load off just as well, but the load stays live.
Hands-on: Draw a relay circuit for a pair of fog lamps: a fuse to terminal 30, a dashboard switch feeding terminal 86, terminal 85 to the return, and terminal 87 to the lamps. Label which parts carry a small current and which carry a large one. If you have an old relay that is not connected to anything, look at the numbers molded on its base and match them to your drawing. Paper and looking only; no work on a real vehicle.
What you will learn
- I can describe the main types of switch used on vehicles.
- I can explain the difference between switching the feed and switching the ground.
- I can explain how a relay works and why it is used.
- I can identify the standard relay terminals 30, 85, 86, 87 and 87a and calculate coil current.
Key words
- momentary switch
- A switch that only stays on while it is pressed, such as a horn push. It springs back when released.
- latching switch
- A switch that stays in the position it was put in until it is moved again, such as a light switch.
- relay
- An electrically operated switch: a small current through a coil makes a magnet that closes heavy-duty contacts.
- changeover relay
- A relay with two outputs: one connected when the coil is off (87a) and one when it is on (87).
- back-EMF
- A voltage spike produced by a coil when its current is switched off. A diode or resistor across the coil absorbs it.
The big ideas
A switch opens and closes a circuit. That sounds simple, but on a vehicle it raises two problems. First, the switches on the dashboard are small and close to the driver, while some loads – headlamps, a heated rear window, a cooling fan, the starter motor – draw large currents. Running thick cables to the dashboard and back would be heavy and would make the switch contacts burn.
The answer is the relay: a small switch sends a small current to the relay's coil, and the relay's heavy contacts, placed close to the load, carry the big current. Today many loads are switched by electronic control units using transistors, which do the same job with no moving parts.
This lesson explains how switches and relays work and how they are drawn; it is not a guide to altering a vehicle's circuits.
Read-through: the teaching steps
Types of switch
Vehicle switches come in many forms:
- Momentary (push-to-make) – horn push, door-ajar switch.
- Latching – light switch, hazard switch.
- Multi-position – wiper switch (off, intermittent, slow, fast), ignition switch.
- Pressure, temperature and position switches – oil pressure warning, brake light switch on the pedal.
Every switch has a current rating. If too much current passes, the contacts arc and burn, raising their resistance.
A simple lighting circuit. On a car the metal body is the return path (ground). Switching the feed or the ground
A switch can be placed on either side of the load:
- Feed (positive) switching – the switch is between the supply and the load. The load is dead when switched off. This is safer, because a short to the body with the switch off does nothing.
- Ground (negative) switching – the load always has a feed, and the switch connects its other side to ground. Many courtesy lamps and warning lamps work this way, and so do many electronic control unit outputs.
Knowing which method a circuit uses, from the wiring diagram, tells a technician where to expect voltage.
How a relay works
A relay has two separate circuits:
- The control circuit: a coil of fine wire. When the dashboard switch sends current through it, the coil becomes an electromagnet.
- The load circuit: a pair of heavy contacts. The magnet pulls a metal armature that closes them.
The coil might draw a fraction of an amp, while the contacts carry tens of amps. When the coil current stops, a spring opens the contacts again.
Standard relay terminals
Most automotive relays use standard terminal numbers:
- 30 – the heavy supply from the battery (through a fuse).
- 85 and 86 – the two ends of the coil. One goes to the control switch, the other to ground or to a feed.
- 87 – the output to the load, connected to 30 when the coil is energized.
- 87a – on a changeover relay, the output connected to 30 when the coil is off.
The terminal numbers are molded on the relay and printed on the wiring diagram, so the two can be matched.
Spikes and suppression
When the current through a coil is switched off, its magnetic field collapses and produces a short, high voltage spike (back-EMF) that can be well over 100 V. It can damage the transistors in electronic control units.
Many relays therefore have a diode or a resistor connected across the coil inside the case. A relay with a diode must be fitted the right way round, and replacement relays must match the original's specification.
Electronic switching
Electronic control units switch many loads directly with transistors (often MOSFETs). These have no contacts to wear, switch very quickly and can measure the current they supply, so they can turn off and store a fault if a load is shorted.
In a body control module, a press of a dashboard button may simply send a message to the module, which then switches the load. Diagnosing such circuits needs the manufacturer's information and a scan tool, used by a trained technician.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.