▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Suspension layouts: MacPherson strut, double wishbone and multi-link – Motor Vehicle Theory motor mechanics lesson

Lesson 80 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Compare the main ways of locating a car's wheels – beam axles, MacPherson struts, double wishbones and multi-link – and learn how motion ratio links the spring to the wheel.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

The motion ratio questions use squaring and multiplying decimals. Suspension springs and struts store a great deal of energy, so this lesson is theory only. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “A sports car maker and a van maker might choose different suspension layouts for the rear. What would each be trying to achieve?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a MacPherson strut needs no lower arm. The strut locates the top of the hub, but a lower arm (track control arm) is still needed to locate the bottom.
  • Thinking a spring mounted half-way along an arm gives half its rate at the wheel. The rate is reduced by the motion ratio squared, so half-way gives only a quarter of the rate.
  • Thinking independent suspension is always better than a beam axle. A beam axle is strong, simple and cheap, so it suits heavy loads and off-road work. The best layout depends on the vehicle's job.

Hands-on: Build a card model of a double wishbone: cut two arms from card, one shorter than the other, and join them with paper fasteners to a card upright (the hub) and a card base (the body). Move the hub up and down and watch how the top of the hub tilts inwards. Repeat with arms of equal length and compare. No real vehicle is needed.

What you will learn

  • I can explain the difference between dependent and independent suspension.
  • I can describe the MacPherson strut, double wishbone and multi-link layouts and give a strength and a weakness of each.
  • I can explain why unequal-length wishbones help keep the tire flat in a corner.
  • I can use motion ratio to find spring travel and wheel rate.

Key words

independent suspension
Suspension in which each wheel on an axle can move up and down without moving the wheel on the other side.
MacPherson strut
A layout in which a combined spring and shock absorber unit (the strut) also locates the top of the wheel and, at the front, acts as the steering pivot.
wishbone
A suspension arm shaped like a letter A or V, joined to the body at two points and to the hub at one.
multi-link
A layout that locates the wheel with three or more separate links, each set to control one direction of movement.
motion ratio
How far the spring or shock absorber moves for each unit that the wheel moves.

The big ideas

A suspension layout has two jobs. It must let the wheel move up and down over bumps, and it must stop the wheel moving in any other direction – forward, backward or sideways – except where the designer wants a small, controlled change. The parts that do this are the arms, links and struts that join the hub to the body.

Older and heavier vehicles often use a beam axle, where the two wheels are joined, so a bump under one wheel tilts the other. Most cars now use independent suspension at the front and often at the rear, so each wheel moves on its own. The three most common independent layouts are the MacPherson strut, the double wishbone and the multi-link.

Each layout is a compromise between cost, space, weight and how well it keeps the tire flat on the road. This lesson explains how they work and how they compare; the springs inside them store a great deal of energy, so work on them is for trained technicians only.

Read-through: the teaching steps

  1. Dependent and independent

    In a dependent layout, such as a beam axle on leaf springs, the two wheels are joined by a solid axle. It is strong, simple and keeps the wheels parallel to each other, but a bump under one wheel affects the other, and the heavy axle adds unsprung mass.

    In an independent layout, each wheel has its own arms. The ride and grip are better, especially on uneven roads. Many small front-wheel-drive cars use a twist beam at the rear: a cross-beam that twists, a halfway step between the two.

  2. MacPherson strut

    A MacPherson strut combines the shock absorber and the coil spring in one tall unit. The bottom of the strut is fixed to the hub; the top is fixed to the body through a mounting with a bearing, so at the front the whole strut turns when the car is steered. A single lower arm locates the bottom of the hub.

    • Strengths: few parts, cheap, compact across the car, leaving room for a transverse engine.
    • Weaknesses: tall, so it needs height under the hood; the camber changes as the suspension moves and the car rolls, and side forces load the shock absorber's sliding parts.
  3. Double wishbone

    A double wishbone layout uses two arms, one above the other, each joined to the body at two points and to the hub by a ball joint. The spring and shock absorber sit between one arm and the body.

    If the upper arm is shorter than the lower arm, the top of the wheel moves inwards as the wheel rises. That gives the outer wheel in a corner more negative camber, which cancels some of the body's lean and keeps the tread flatter on the road. Double wishbones give the designer close control of the wheel, but they take more space and cost more.

  4. Multi-link

    A multi-link layout replaces the wishbones with three, four or five separate links, each joined by bushes or ball joints. Because each link controls one direction, the designer can tune camber, toe and how the wheel moves under braking or acceleration more freely.

    Multi-link is common at the rear of many cars. It gives very good control but has more parts and more bushes to wear.

  5. Motion ratio

    The spring is often mounted part-way along an arm, not right at the wheel. Then it moves less than the wheel does. The motion ratio (MR) is spring movement ÷ wheel movement.

    Because the spring moves less and also acts on a shorter lever, its effect at the wheel is reduced twice:

    • spring travel = wheel travel × MR
    • wheel rate = spring rate × MR²
  6. Layouts in a state inspection

    Where a state requires a periodic safety inspection, steering and suspension are checked – Virginia, for example, lists them as one of its 24 inspection steps. Rules are set by each state, so check your own state's official source.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.