Sensors: temperature, position, speed and pressure – Motor Vehicle Theory motor mechanics lesson
Lesson 101 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how the sensors that feed a vehicle's control units turn temperature, position, speed and pressure into electrical signals, and how those signals are read.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
The lesson uses the voltage divider formula and frequency calculations, linked to GCSE/A level physics. It explains how sensors work; testing on a real vehicle is done by trained technicians. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Many sensors are now "smart" and send digital messages instead of a simple voltage. What are the advantages for the ECU, and what might be harder for a technician?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a coolant sensor's resistance rises as it gets hotter. Most coolant sensors are NTC thermistors: resistance falls as temperature rises.
- Thinking an inductive sensor gives the same signal at all speeds. Its voltage and frequency both rise with speed; at very low speed the signal can be too weak to read.
- Thinking a reading of exactly 0 V or 5 V is simply an extreme value. Most sensors are designed to stay inside about 0.5–4.5 V. A rail-to-rail reading usually means a wiring fault.
Hands-on: Build a paper "voltage divider calculator": make a table with a fixed resistor of 2,500 Ω and sensor resistances of 10,000 Ω, 5,000 Ω, 2,500 Ω, 1,000 Ω and 300 Ω. Work out the signal voltage for each with V = 5 × Rs ÷ (2,500 + Rs), then plot signal voltage against sensor resistance. Which end of the graph is a cold engine? Paper and calculator only.
What you will learn
- I can explain how an NTC thermistor and a voltage divider give a temperature signal.
- I can describe how a potentiometer gives a position signal from a 5 V reference.
- I can compare inductive and Hall-effect speed sensors and calculate signal frequency.
- I can describe how a pressure sensor works and explain what makes a sensor signal implausible.
Key words
- NTC thermistor
- A temperature sensor whose resistance falls as its temperature rises (negative temperature coefficient).
- voltage divider
- Two resistances in series across a supply. The voltage at the join depends on the ratio of the two resistances.
- potentiometer
- A resistor with a sliding contact. The voltage at the slider shows its position.
- Hall-effect sensor
- A sensor that gives a clean on-off (square wave) signal as a magnetic field changes, even at very low speed.
- inductive sensor
- A coil and magnet that make an AC voltage as steel teeth pass; the voltage and frequency rise with speed.
The big ideas
An electronic control unit is only as good as the information it receives. Sensors are its eyes and ears: they turn physical quantities such as temperature, position, speed and pressure into voltages or pulses the ECU can measure. The US Department of Energy notes that the electronic control module controls the fuel mixture and ignition timing and also monitors the vehicle and detects problems – all of which depends on sensor signals.
Most sensors fall into a few families. Some change their resistance, so the ECU reads them through a voltage divider. Some are fed a 5 V reference and return a fraction of it. Some generate their own signal, and others switch on and off to give a pulse train whose frequency shows speed.
Knowing which family a sensor belongs to tells a technician what signal to expect. This lesson explains how sensors work; testing them on a vehicle is work for a trained technician using the manufacturer's data.
Read-through: the teaching steps
Temperature: the NTC thermistor
Coolant, intake air, fuel and oil temperatures are usually measured with NTC thermistors. As the sensor warms up, its resistance falls – from several thousand ohms when cold to a few hundred ohms when hot (the manufacturer's data gives the exact figures).
The ECU puts the thermistor in series with a fixed resistor across its 5 V supply. This is a voltage divider. The ECU measures the voltage across the sensor:
- V(signal) = 5 × R(sensor) ÷ (R(fixed) + R(sensor)).
Cold engine, high resistance, high signal voltage; hot engine, low resistance, low signal voltage.
Position: the potentiometer
A throttle or pedal position sensor is often a potentiometer: a resistance track with a 5 V reference at one end, the 0 V return at the other, and a wiper that moves with the throttle or pedal.
- The signal is a fraction of 5 V: at half travel, about 2.5 V.
- Most electronic throttles use two sensors with different signal ranges, so the ECU can compare them and spot a fault.
Some modern position sensors are non-contact (Hall-effect or inductive), so there is no track to wear out, but the output voltage behaves the same way.
Speed: inductive sensors
An inductive sensor has a permanent magnet wrapped in a coil, close to a steel toothed wheel (a reluctor). As each tooth passes, the magnetic field changes and a voltage is induced in the coil.
- The output is AC. Its frequency equals the number of teeth passing per second.
- Its voltage rises with speed – at very low speeds the signal is weak.
Crankshaft sensors often use a wheel with a gap of missing teeth (for example 60 − 2) so the ECU can tell where top dead center is.
Speed: Hall-effect sensors
A Hall-effect sensor contains a semiconductor chip that responds to a magnetic field. With electronics inside, it gives a clean square-wave signal – on or off – that does not depend on speed.
Because it works right down to zero speed, it suits camshaft position and many ABS wheel-speed sensors. It needs a power supply from the ECU, so it has three wires (supply, signal, 0 V return) or two wires in some current-signal designs.
Pressure sensors
A manifold absolute pressure (MAP) sensor, a fuel rail pressure sensor or an air-conditioning pressure sensor usually contains a thin silicon diaphragm with tiny resistors on it. Pressure bends the diaphragm, changing the resistances, and electronics inside convert this into a voltage between about 0.5 V and 4.5 V.
Keeping the signal away from 0 V and 5 V lets the ECU spot faults: a reading at 0 V suggests a short to 0 V or a broken supply; a reading at 5 V suggests an open circuit or a short to the reference.
Plausibility and fault codes
The ECU constantly checks that each sensor makes sense:
- Range – is the voltage inside the allowed window?
- Rate of change – can the value really change that fast?
- Plausibility – does it agree with other sensors? (A coolant temperature of −40 °C on a warm engine is implausible.)
If a check fails, the ECU stores a fault code, may light a warning lamp and may substitute a default value. A technician then confirms the fault with live data and measurements against the manufacturer's figures.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.