Noise, vibration and harshness: tracing the source – Motor Vehicle Theory motor mechanics lesson
Lesson 112 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how technicians track down noises and vibrations by asking what they change with – road speed, engine speed, braking or turning – and how the frequency of a vibration points to the part causing it.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson links frequency, rotation and speed (GCSE/A level physics) to real diagnostic reasoning. The activity uses a bicycle pushed by hand with an adult present; no work is done on a car. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Electric cars are very quiet, so drivers notice noises that a gasoline engine used to hide. How might this change the work of NVH engineers?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the place where the driver feels a vibration is where it starts. Vibrations travel through mountings and the body. The steering wheel may shake from a front wheel problem; the seat may buzz from the exhaust.
- Thinking a vibration that changes with speed must be the engine. Change gear at the same road speed: if the vibration stays the same, it follows road speed, pointing to wheels, tires or shafts.
- Replacing parts that "might" be noisy without confirming the source. Confirm the noise with the customer, sort it by what it changes with, and measure or listen before replacing anything.
Hands-on: With an adult, find the rolling diameter of a bicycle wheel by measuring how far it travels in one turn. Then work out how many times a second it turns at 3 m/s (a brisk walk). Tape a small piece of card to the frame so it lightly flicks the spokes, push the bike slowly and then faster, and listen to how the pitch rises with speed. Bicycle and card only; the bike is pushed, not ridden.
What you will learn
- I can explain what noise, vibration and harshness (NVH) mean.
- I can explain how to tell road-speed, engine-speed and load-related vibrations apart.
- I can calculate the rotation frequency of a wheel and of an engine and link frequency to likely sources.
- I can describe the safe, supervised ways technicians gather NVH evidence.
Key words
- NVH
- Noise, vibration and harshness: sounds and shakes that the driver hears or feels and finds unpleasant.
- frequency
- How many times something happens per second, measured in hertz (Hz).
- order
- A vibration's frequency compared with how fast a part rotates. A first-order vibration happens once per revolution.
- transfer path
- The route by which a vibration travels from its source, through mountings and the body, to the driver.
The big ideas
A noise or a vibration is one of the most common complaints a technician hears, and one of the hardest to pin down. The driver may feel a shake through the steering wheel or the seat, or hear a hum, whine, knock or squeak, but the source could be anywhere in the vehicle.
The key idea is that every rotating part makes its own rhythm. Wheels and tires turn at a rate set by road speed. The engine turns at a rate set by engine speed. Propeller shafts, gears and pulleys each turn at their own rates. So the first question is always: what does the noise or vibration change with?
This lesson explains how that reasoning works and the simple math behind it. Road tests and checks on a vehicle are done by a qualified technician, and nobody looks under a vehicle that is running or supported only on a jack (HSE).
Read-through: the teaching steps
Noise, vibration and harshness
The three overlap:
- Noise – what you hear. Human hearing covers roughly 20 Hz to 20,000 Hz.
- Vibration – what you feel, usually at lower frequencies, through the steering wheel, seat or pedals.
- Harshness – how the car responds to sharp inputs such as bumps or potholes.
Every vibration has a source (the part that shakes), a transfer path (mountings, bushes, body panels) and a responder (the part that the driver feels or hears). Fixing the source is usually the real repair.
What does it change with?
A careful road test with a qualified driver sorts the problem into a group:
- Road speed – changes with vehicle speed, whatever gear is used: wheels, tires, hub bearings, propeller or drive shafts.
- Engine speed – changes with rpm, even when stationary: engine, ancillaries, exhaust, engine mountings.
- Load or torque – appears accelerating or coasting: drive shaft joints, mountings, final drive.
- Braking – appears only when braking: brake discs, pads, callipers.
- Turning – appears only when cornering: constant-velocity joints, hub bearings, steering parts.
Changing gear at the same road speed is a classic test: if the vibration stays, it is road-speed related; if it changes, it is engine-speed related.
Wheel and tire frequency
A tire turns once for every circumference of road it covers:
- wheel frequency (Hz) = road speed (m/s) ÷ tire circumference (m);
- circumference = π × rolling diameter.
At highway speeds a car wheel turns about 12–15 times a second. An out-of-balance wheel or a tire with a bulge gives a first-order vibration at exactly that frequency – often felt through the steering if it is a front wheel, or through the seat if it is a rear wheel.
Engine frequency and firing order
Engine rotation frequency (Hz) = rpm ÷ 60.
- An imbalance in the crankshaft or a pulley gives first-order vibration.
- In a four-stroke engine each cylinder fires once every two revolutions. A four-cylinder engine has two firing events per revolution, so its firing frequency is second order: 2 × rpm ÷ 60.
- A misfire breaks the regular pattern and makes a lumpy vibration at a lower frequency.
Worn engine mountings let these normal vibrations into the body.
Common noises and their clues
- Hum or drone rising with road speed, changing when cornering – hub bearing.
- Clicking when turning on full lock under power – outer constant-velocity joint.
- Squeal when starting from cold or on full steering lock – a slipping auxiliary belt.
- Knock over bumps – suspension or steering joints, or a loose part.
- Rumble or vibration only when braking – distorted brake discs.
- Rattle at certain engine speeds – a loose heat shield on the exhaust.
These are starting points for testing, not diagnoses.
Gathering evidence safely
Technicians use several aids, always with the vehicle secured:
- a road test with the customer as passenger, to agree what the noise is;
- stethoscopes or "chassis ears" – microphones clipped to parts, listened to from inside the car during a road test;
- electronic vibration analysers that measure frequency;
- careful inspection on a proper lift, with the engine off.
Being trapped under a badly supported vehicle is one of the most serious shop hazards. Never go under a vehicle supported only on a jack; learners look and listen only, with a qualified adult.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Fault-finding lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.