Lubrication systems: pump, filter and galleries – Motor Vehicle Theory motor mechanics lesson
Lesson 37 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Follow the oil from the bottom of the engine, through the pump, relief valve and filter, along the galleries to the bearings, and find out how a thin film of oil keeps metal parts apart.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson explains how engine lubrication works. Hot oil can burn and used engine oil can harm the skin; work on the lubrication system is for trained technicians. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think most engine wear is said to happen in the first few seconds after a cold start?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the oil pump makes the pressure on its own. The pump makes flow. Pressure comes from that flow being forced through small bearing clearances and is limited by the relief valve. Worn bearings let oil escape and pressure drops.
- Thinking the bypass valve means the filter is pointless. The bypass opens only when the element is blocked or the oil is very thick. Normally all the oil is filtered.
- Thinking that oil's only job is to reduce friction. It also cools the pistons and bearings, helps the rings seal, carries dirt to the filter and protects against corrosion.
Hands-on: Hydrodynamic film model: with an adult, put a few drops of cooking oil on a smooth plate and lay a flat plastic lid on it. Push the lid quickly along and notice how it seems to glide on the oil; then wipe the plate dry and try again. Draw a labeled flow diagram of the lubrication system from reservoir to bearings and back, marking the strainer, pump, relief valve, filter, bypass valve, main gallery and bearings. Do not use engine oil: used engine oil is harmful to skin. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look – for example at the oil filler cap and dipstick handle.
What you will learn
- I can list the jobs engine oil does besides reducing friction.
- I can trace the path of oil through a pressure-fed lubrication system.
- I can explain what the pressure relief valve and the filter bypass valve do.
- I can explain how a hydrodynamic oil film separates a shaft from its bearing.
- I can calculate oil pump delivery from displacement and speed, and a force from pressure and area.
Key words
- oil pan
- The reservoir bolted to the bottom of the engine that holds the oil when it drains back.
- oil pump
- A positive-displacement pump, driven by the engine, that pushes oil round the system under pressure.
- pressure relief valve
- A spring-loaded valve that opens to return oil when the pressure gets too high, protecting the pump, filter and seals.
- oil gallery
- A passage drilled or cast through the block and head that carries oil to the bearings and other parts.
- hydrodynamic film
- A wedge of oil dragged between a spinning shaft and its bearing that builds up enough pressure to keep the metal surfaces apart.
The big ideas
An engine has hundreds of metal surfaces sliding or rolling over each other at high speed: crankshaft bearings, connecting rods, pistons in their bores, camshafts and valve gear. Without lubrication they would heat up, wear and seize within moments. Engine oil keeps them apart.
Oil does several jobs at once: it reduces friction and wear, carries heat away from the pistons and bearings, helps the piston rings seal, carries dirt to the filter, and protects against corrosion. Almost every car engine uses a pressure-fed (forced) system: a pump draws oil from the oil pan and pushes it through a filter and along galleries to the parts that need it, before it drains back.
Owner's manuals list engine oil among the regular checks a driver should make. This lesson explains the theory. It is not a repair guide: hot oil can burn, and frequent skin contact with used engine oil can harm the skin. Work on the lubrication system is for trained technicians.
Read-through: the teaching steps
The oil's journey
Follow the oil round:
- It sits in the oil pan at the bottom of the engine.
- The pump draws it up through a pickup tube with a mesh screen that stops large debris.
- The pump pushes it to the oil filter, which removes fine particles.
- It enters the main gallery running along the block.
- Drillings carry it to the crankshaft main bearings, and holes through the crankshaft carry it on to the connecting rod bearings.
- Other passages feed the cylinder head: camshaft bearings, valve gear and often the timing chain tensioner.
- It drains back by gravity to the oil pan.
The oil pump
Oil pumps are positive-displacement pumps: each turn moves a fixed volume of oil, so delivery rises in step with engine speed. Common types are the gear pump (two meshing gears), the rotor pump (an inner rotor turning inside an outer rotor) and the vane pump. They are driven from the crankshaft, a camshaft or a chain.
Delivery = displacement per revolution × pump speed. A pump moving 10 cm³ per revolution at 3,000 rpm delivers 30,000 cm³ (30 liters) a minute. Many modern engines use variable-displacement pumps that deliver only what the engine needs, saving power.
Controlling the pressure
Because a positive-displacement pump delivers more and more oil as the engine speeds up, the pressure would keep rising, especially with cold, thick oil. A pressure relief valve – a ball or plunger held shut by a spring – opens when the pressure force on it overcomes the spring, and lets the extra oil return to the pump inlet or the reservoir.
The force on the valve is pressure × area (F = p × A). The spring is chosen so the valve opens at the pressure the manufacturer wants. Oil pressure is the result of the pump pushing oil through the small clearances of the bearings; worn bearings let oil escape more easily, so pressure falls.
The oil filter
Most engines use a full-flow filter: all the oil from the pump passes through a pleated paper or synthetic element before reaching the bearings.
Two small valves are often built in:
- a bypass valve, which opens if the element is blocked or the oil is very cold and thick, so the bearings still get oil (unfiltered oil is better than none);
- an anti-drain-back valve, which stops oil draining out of the filter when the engine is stopped, so pressure builds quickly at the next start.
The filter and oil are changed at intervals the manufacturer sets.
How a bearing film works
A plain bearing (shell bearing) is a smooth sleeve with a tiny clearance around the shaft. When the shaft spins, it drags oil into the narrowing wedge on the loaded side. The oil is pressed into this wedge and builds up enough pressure to lift the shaft off the bearing. This is hydrodynamic lubrication: the shaft floats on a film of oil much thinner than a sheet of paper.
The film needs a steady supply of oil and the right viscosity. Wear is highest at start-up, before the film forms, and when oil pressure is low, which is why the oil warning light is so important.
Other jobs and other designs
Oil jets in many engines spray oil onto the underside of the pistons to cool them. Turbochargers are fed oil for their high-speed bearings. Some engines have an oil cooler, a small heat exchanger cooled by coolant or air.
Racing and some high-performance engines use a dry sump system: a separate tank holds the oil and scavenge pumps take it from the bottom of the engine, so it cannot surge away from the pickup in hard cornering. An oil pressure switch or sensor works the warning light; if the light comes on while driving, owner's manuals advise stopping safely and switching off.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Cooling and lubrication lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
About this lesson
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.