▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Ignition systems: coils, plugs and timing – Motor Vehicle Theory motor mechanics lesson

Lesson 44 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how a 12-volt battery makes a spark of many thousands of volts, what happens at the spark plug, and why the spark must arrive earlier as the engine speeds up.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains how gasoline ignition systems work. Ignition systems produce very high voltages that can give a severe shock: any work on them is for trained technicians only. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Before electronic engine control, ignition advance was set by weights and springs inside the distributor. What advantages does a control unit with a knock sensor have?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the coil makes high voltage while current is flowing steadily in the primary. The high voltage comes when the primary current is switched off and the magnetic field collapses suddenly.
  • Thinking the spark should happen exactly at top dead center. The flame needs time to build pressure, so the spark comes before top dead center, and earlier at higher speed.
  • Thinking a hotter spark plug always gives more power. Heat range is about how fast the tip loses heat. Too hot a plug can cause pre-ignition; use the plug the manufacturer specifies.

Hands-on: Timing wheel model: cut a card circle, mark it in 10° steps, and mark top dead center at the top. Pin it to a board so it turns. Put a pointer at 0° and practice placing a sticker for the spark at 10°, 20° and 30° before top dead center. Then work out, for 1,000, 3,000 and 6,000 rpm, how many milliseconds before TDC a 25° spark happens, and plot the results. Do not go near a real ignition system: it can give a severe electric shock.

What you will learn

  • I can explain how an ignition coil uses electromagnetic induction to make a very high voltage.
  • I can calculate a coil's output voltage from its turns ratio.
  • I can describe the parts of a spark plug and what heat range means.
  • I can explain why ignition timing is advanced at higher engine speed and retarded when knock is detected.
  • I can convert ignition advance in crankshaft degrees into time.

Key words

ignition coil
A transformer with a primary winding of few turns and a secondary winding of many thousands of turns, which turns the battery supply into a very high voltage for the spark.
spark plug
The part screwed into the cylinder head that makes the spark across a small gap between two electrodes.
ignition timing
When the spark happens, measured in degrees of crankshaft rotation before top dead center (BTDC).
ignition advance
Making the spark happen earlier (more degrees before top dead center).
knock sensor
A sensor on the engine block that picks up the vibration of knock, so the control unit can retard the timing.

The big ideas

In a gasoline engine, the US Department of Energy explains, the air–fuel mixture is ignited by the spark plug, and the electronic control module controls the ignition timing. To jump the gap at the plug inside a compressed cylinder, the spark needs many thousands of volts – yet the car's electrical system is only about 12 volts. The ignition coil bridges the gap using electromagnetic induction.

Timing matters as much as voltage. The burning mixture takes a short, fairly fixed time to build up full pressure, so the spark must come before the piston reaches the top. As the engine speeds up, the piston covers more degrees in that time, so the spark must come earlier still. The control unit sets this for every spark, using engine speed, load, temperature and a knock sensor.

This lesson explains the theory. It is not a repair guide: ignition systems produce very high voltages that can give a severe shock, so they are for trained technicians only.

Read-through: the teaching steps

  1. How the coil makes high voltage

    An ignition coil is a transformer. Its primary winding has relatively few turns of thicker wire; its secondary winding has many thousands of turns of very fine wire, wound around the same iron core.

    While current flows in the primary, it builds a magnetic field in the core. The control unit then switches the primary current off very suddenly. The field collapses, and the rapid change induces a voltage in both windings. Because the secondary has far more turns, its voltage is far higher – high enough to jump the plug gap.

    The time the primary is switched on to build the field is called the dwell.

  2. Turns ratio

    For a transformer, the voltages are roughly in proportion to the numbers of turns:

    Vs ÷ Vp = Ns ÷ Np

    If a coil has 150 primary turns and 15,000 secondary turns, the turns ratio is 100. When the primary current is cut, a pulse of a few hundred volts appears across the primary; with a ratio of 100, a 300 V primary pulse gives about 300 × 100 = 30,000 V at the secondary. Real coils lose some energy, so this is an ideal estimate.

  3. Coil-on-plug and older layouts

    Older cars used one coil and a distributor, a rotating switch that sent each spark to the right cylinder through high-tension leads. Later 'wasted spark' systems used one double-ended coil for each pair of cylinders.

    Most modern engines use coil-on-plug: a small coil sits directly on top of each spark plug. There are no long high-tension leads to leak, and the control unit can set the timing of each cylinder separately.

  4. The spark plug

    A spark plug has a central electrode, insulated by a ceramic body, and a ground electrode joined to the metal shell. The spark jumps the small gap between them. The gap size is set by the manufacturer.

    The heat range describes how quickly the plug's tip passes heat to the cylinder head. A plug must run hot enough to burn off deposits but not so hot that its tip lights the mixture early. The manufacturer's data gives the right plug for each engine. Worn plugs need a higher voltage to fire and can cause misfires.

  5. Why timing advances with speed

    After the spark, the flame takes a short time to spread through the mixture and build up full pressure. For the best push, peak pressure should come a little after top dead center.

    At higher engine speed, the crankshaft turns more degrees in that time, so the spark must come more degrees before top dead center. At light load the mixture is thinner and burns more slowly, so more advance is used too. The control unit reads speed and load and looks up the best timing from a map stored in its memory.

  6. Knock control

    If the spark is too early, or the mixture is too hot, the last part of the mixture can explode on its own before the flame reaches it. That is knock (detonation): a sharp metallic pinging that can damage pistons.

    A knock sensor, a small microphone-like sensor bolted to the block, picks up the vibration. The control unit then retards (delays) the timing on that cylinder until the knock stops, and gradually advances it again. This lets engines run close to their best timing safely, and adapt to fuel quality.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.