▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Exhaust gas recirculation and evaporative emission control – Motor Vehicle Theory motor mechanics lesson

Lesson 50 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how feeding a little exhaust gas back into the engine cuts oxides of nitrogen, and how a charcoal canister stops gasoline vapor escaping from the fuel tank.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains EGR and evaporative emission control. EGR parts get very hot and fuel vapor is highly flammable: work on these systems is for trained technicians. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “EGR cuts NOx but can increase soot on a diesel. How would you explain this trade-off to someone who thinks one setting can make every pollutant zero?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking EGR is used at full power. At full load every bit of oxygen is needed for power, so the EGR valve is closed. EGR is used mainly at light and medium load.
  • Thinking recirculated exhaust gas burns again in the cylinder. It has already burnt. It is there to dilute the charge and absorb heat, not to be burnt.
  • Thinking a loose gas cap only matters if fuel spills. Vapor escapes from a poorly sealed cap, and the leak check may light the engine warning lamp.

Hands-on: Charcoal sponge with an adult: put a few drops of vanilla essence on a cotton pad in a clean jar and smell it. In a second jar, put a spoonful of aquarium activated carbon over a second scented pad, close the lid, wait an hour, and compare the smell when you open each jar. The carbon soaks up much of the vapor, like a canister. Then draw both systems on paper with arrows for gas flow. Use no gasoline or other fuel for this activity.

What you will learn

  • I can explain how exhaust gas recirculation lowers combustion temperature and reduces NOx.
  • I can describe the parts of an EGR system and why EGR coolers are used.
  • I can explain how an evaporative emission system captures fuel vapor and purges it into the engine.
  • I can link common EGR and evaporative system faults to their symptoms.
  • I can calculate an EGR rate and the oxygen fraction of a diluted charge.

Key words

exhaust gas recirculation (EGR)
Returning a controlled amount of exhaust gas to the inlet so that it dilutes the fresh charge and lowers the peak combustion temperature.
EGR valve
The valve, usually electrically controlled, that sets how much exhaust gas is recirculated.
EGR cooler
A heat exchanger, cooled by engine coolant, that cools the recirculated gas so it is denser and keeps combustion cooler.
charcoal canister
A container of activated carbon that soaks up fuel vapor from the tank so it does not escape to the air.
purge valve
A valve the control unit opens to draw stored fuel vapor from the canister into the engine, where it is burnt.

The big ideas

Two quieter emissions systems work alongside the catalysts. Exhaust gas recirculation tackles oxides of nitrogen at their source. NOx forms when combustion is very hot and has oxygen to spare. If some of the fresh charge is replaced with exhaust gas – which has already burnt and carries little oxygen – the flame burns cooler, and much less NOx forms.

Evaporative emission control tackles a different source of pollution: gasoline vapor. Gasoline evaporates easily, especially on a hot day, and the vapor from a fuel tank is a hydrocarbon pollutant. The evaporative system traps it in a charcoal canister and later feeds it into the engine to be burnt. In New York, for example, the DMV's low-enhanced emissions test for older vehicles includes checking the gas cap, which is part of this system.

The US Department of Energy notes that the engine's electronic control module controls the emissions system. This lesson explains how these two systems work. It is not a repair guide: EGR parts get very hot and fuel vapor is highly flammable, so work on them is for trained technicians.

Read-through: the teaching steps

  1. How EGR cuts NOx

    Exhaust gas is mostly nitrogen, carbon dioxide and water vapor. These do not burn again. When some of it is mixed with the fresh charge:

    • there is less oxygen in each cylinder, so less fuel burns in the same space at light load;
    • the inert gases soak up heat, so the peak flame temperature is lower.

    Lower peak temperature means much less NOx. EGR is used mainly at light and medium load, where it costs little power. At full load the control unit closes the EGR valve, because all the oxygen is needed.

  2. The parts of an EGR system

    A pipe connects the exhaust to the inlet, with the EGR valve controlling the flow. Modern valves are worked by an electric motor and have a position sensor, so the control unit can check the valve has moved as commanded.

    Many engines, especially diesels, have an EGR cooler: a small heat exchanger cooled by engine coolant. Cooler gas is denser and keeps the charge cooler, which helps cut NOx further. Some diesels take gas from after the particulate filter (low-pressure EGR), so it is clean of soot.

  3. EGR on gasoline engines and with valve timing

    Gasoline engines use EGR too. As well as cutting NOx, it lets the throttle open wider for the same power, which reduces pumping losses and improves efficiency at light load.

    Many modern engines also get 'internal EGR' without a separate valve: variable valve timing holds the exhaust and inlet valves open together for a moment, so some exhaust gas stays in the cylinder or is drawn back.

  4. EGR faults

    EGR gas carries soot and oil vapor, especially on diesels, so the valve and passages can become coated with carbon:

    • A valve stuck open lets exhaust in at idle and when it should not, causing rough idle, stalling, black smoke on a diesel, or hesitation.
    • A valve stuck shut or a blocked passage stops EGR, so NOx rises and the control unit may detect an EGR flow fault and light the engine warning lamp.
    • A leaking EGR cooler can let coolant into the inlet: a falling coolant level and white smoke.

    A technician uses live data and the manufacturer's tests to find which.

  5. Evaporative emission control

    Gasoline vapor from the tank is led to a charcoal canister. Activated carbon has an enormous internal surface area and holds the vapor like a sponge. A vent lets air in and out of the canister so the tank does not build pressure or vacuum.

    When the engine is warm and running, the control unit opens the purge valve. Intake manifold vacuum draws fresh air through the canister, picking up the stored vapor and carrying it into the engine to be burned. The control unit allows for this extra fuel using the oxygen sensor. The gas cap seals the system; a missing or loose cap lets vapor escape.

  6. Checking for leaks

    Many vehicles test their own evaporative system for leaks. The control unit closes the vent valve and uses engine vacuum or a small pump to change the pressure in the tank and canister, then watches a pressure sensor. If the pressure creeps back too quickly, there is a leak, and the check engine light may come on.

    The most common cause is simple: a gas cap that is loose, missing or has a damaged seal. Other faults include a purge valve stuck open (which can make the engine run rich or hard to start after refueling) or a cracked hose. In New York, for example, the DMV's low-enhanced test for older vehicles checks the gas cap; inspection rules are set by each state.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.