▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Engine mechanical testing: compression and leak-down (theory) – Motor Vehicle Theory motor mechanics lesson

Lesson 32 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out what compression and leak-down tests tell a technician about the inside of an engine, and how to interpret the numbers they produce.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This is explanation for understanding, not a repair guide. Compression and leak-down tests involve a turning engine, hot parts and compressed air, and are for trained technicians following the manufacturer's procedure. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a good technician carry out more than one test before telling a customer an engine needs expensive work?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a compression test shows exactly which part is leaking. It shows that a cylinder is low, not why. A wet test or a leak-down test is needed to find where the pressure goes.
  • Judging one reading on its own. Readings depend on cranking speed, temperature and altitude. Compare the cylinders with each other and with the manufacturer's data.
  • Thinking that a rise in a wet test means the valves are worn. Oil seals the rings, not the valves. A big rise points to the rings; little change points to valves or the gasket.

Hands-on: Make a model of the three leak paths with a plastic syringe (no needle) and your finger. Seal the tip with your finger and push the plunger: the air springs back because it is sealed. Then think about where air could escape in a real cylinder – past the plunger seal (rings), through the tip (valves) – and draw a table of the leak-down clues: where the air is heard, and what part is leaking. If you watch a real test, do it only in a workshop with a qualified technician doing all the work, wearing eye protection, and only look.

What you will learn

  • I can explain why a cylinder must seal well for an engine to run properly.
  • I can describe what a compression test measures and what it cannot tell you.
  • I can explain what a leak-down test measures and how the place where air escapes points to the leaking part.
  • I can calculate percentage differences between cylinders and percentage leakage.
  • I can explain why these tests are done only by trained technicians.

Key words

compression test
A test that measures the highest pressure each cylinder reaches while the engine is turned over by the starter.
leak-down test
A test that fills a cylinder with compressed air, with the piston at the top and both valves shut, and measures what percentage of the air leaks away.
wet test
A compression test repeated after a little oil is put into the cylinder. The oil briefly seals the piston rings.
piston rings
Springy metal rings around the piston that seal it against the cylinder wall.
head gasket
The seal between the cylinder head and the cylinder block. It keeps gas, coolant and oil in their own passages.

The big ideas

This is explanation for understanding, not a repair guide.

An engine can only make power if each cylinder holds its pressure. During the compression and power strokes the cylinder is sealed by the piston rings at the bottom, the valves at the top and the head gasket between the head and the block. If any of these leaks, the cylinder loses pressure, burns its fuel poorly and may misfire.

Two classic tests show how well each cylinder seals. A compression test measures the peak pressure each cylinder reaches. A leak-down test measures how much air escapes from a sealed cylinder, and where it goes. Both are done in a workshop by trained technicians, who disable the ignition and fuel systems first and follow the manufacturer's data: high cylinder pressure, a turning engine and compressed air can all cause injury. Here you will learn what the tests show and how to read the results.

Read-through: the teaching steps

  1. What seals a cylinder

    Think of a cylinder as a container with three possible leaks:

    • past the piston rings into the crankcase;
    • past the inlet or exhaust valves into the manifolds;
    • through the head gasket, into a coolant passage, an oil passage or the next cylinder.

    A good engine loses very little through any of them. Wear, burning and overheating can open up a leak. The drawing on the lesson page shows the four strokes and where the valves sit.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. The compression test

    In a compression test, a gauge is fitted in place of the spark plug (or glow plug or injector on a diesel), and the engine is turned over by the starter for a few revolutions. The gauge holds the highest pressure reached.

    The actual figure depends on the engine's compression ratio, how fast the starter turns it, the altitude and the temperature, so the manufacturer's data gives the expected range. Often the most useful thing is to compare the cylinders with each other: a healthy engine gives similar readings in every cylinder.

  3. Comparing cylinders

    A simple way to compare is to work out how far each reading is below the highest one, as a percentage:

    percentage below highest = (highest − reading) ÷ highest × 100.

    One low cylinder points to a problem in that cylinder. Two low cylinders side by side can point to a head gasket leaking between them. All cylinders evenly low on a high-mileage engine can point to general wear, but could also be a slow-turning starter, so technicians interpret results with care.

  4. The wet test

    If a cylinder reads low, a technician may repeat the test after a little oil is put into the cylinder. The oil briefly seals the gap around the piston rings.

    • If the reading rises a lot, the rings (or the cylinder wall) are likely to be leaking.
    • If it hardly changes, the leak is probably at a valve or the head gasket, which the oil cannot seal.

    This is reasoning from evidence: change one thing and see what happens.

  5. The leak-down test

    A leak-down tester feeds compressed air through a calibrated restriction into the cylinder, with the piston at top dead center on the compression stroke so both valves are shut. Two gauges show the supply pressure and the cylinder pressure, and the tester reads the difference as a percentage leakage.

    The big advantage is that the technician can listen and look for where the air comes out:

    • from the oil filler or crankcase breather – piston rings;
    • from the exhaust tailpipe – an exhaust valve;
    • from the air intake – an inlet valve;
    • bubbles in the coolant – head gasket or cracked head;
    • from the next cylinder's spark plug hole – head gasket between cylinders.
  6. Why these tests are for trained technicians

    The tests involve cranking an engine with the ignition and fuel disabled, removing plugs from a hot engine, and putting compressed air into a cylinder. Air pressure on a piston that is not exactly at top dead center can turn the crankshaft suddenly. A technician follows the manufacturer's procedure, uses the right adaptors and wears eye protection.

    As a learner, your job is to understand the evidence: what each test measures and how a pattern of results leads to a likely cause.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.