▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Dial gauges, feeler gauges and straight edges – Motor Vehicle Theory motor mechanics lesson

Lesson 16 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how dial gauges, feeler gauges and straight edges measure wobble, gaps and flatness to hundredths of a millimeter, and how to work out run-out.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains precision gauges and run-out calculations. The activity uses a steel rule and paper at home or school. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why is the largest gap, rather than the average, used to judge whether a surface is flat?”
  4. Later: the homework, then the practice test.

Watch out for

  • Taking the run-out as the highest reading only. Run-out is highest minus lowest; with negative readings, subtracting a negative adds.
  • Averaging flatness readings. Distortion is the largest gap found, not the mean.
  • Thinking a feeler blade should be pushed hard to be sure. It should slide with a light drag; forcing gives false readings.

Hands-on: With a teacher, check how flat things are at home or school: lay a steel rule on edge across a table, a book and a tile, and see if light shows underneath. Try slipping folded paper (about 0.1 mm per sheet) into any gaps to estimate their size. Record your results in a table.

What you will learn

  • I can describe a dial gauge, feeler gauges and a straight edge.
  • I can read a dial gauge and calculate total run-out.
  • I can use stacked feeler blades to find a gap.
  • I can explain how flatness is checked in several directions.
  • I can explain the set-up errors that spoil precise readings.

Key words

dial gauge
An instrument whose plunger moves a needle round a dial to show small movements, often in 0.01 mm divisions.
feeler gauge
A set of thin steel blades of known thickness for measuring small gaps.
straight edge
A precision ground bar used as a reference to check flatness.
run-out
The total variation measured as a part rotates; also called total indicated reading (TIR).
end float
The amount a shaft can move along its own axis.

The big ideas

Not every measurement is a size. Often the question is: does it wobble, is it flat, or how big is that gap? For these, technicians use the dial gauge, the feeler gauge and the straight edge.

A dial gauge, mounted rigidly, shows how much a surface moves as a part rotates – the run-out of a shaft or disc, or the end float of a crankshaft. Feeler gauges are thin blades of known thickness that measure small gaps. A straight edge laid across a surface, with feeler blades to measure any gap underneath, checks flatness – for example of a cylinder head.

This lesson explains how the tools work and how to calculate results. The limits for any real part come from the manufacturer's data, and measuring real engine and brake parts is work for trained technicians.

Read-through: the teaching steps

  1. The dial gauge

    A dial gauge has a spring-loaded plunger connected through gears to a needle. A typical metric gauge has 100 divisions of 0.01 mm, so one turn of the needle is 1 mm; a small counter dial counts turns. The bezel rotates so the needle can be set to zero at the start.

  2. Measuring run-out

    The gauge is mounted rigidly on a magnetic or clamp stand, the plunger square to the surface and slightly preloaded. The part is turned slowly through a full revolution.

    Total run-out = highest reading − lowest reading.

    Excessive run-out on a brake disc can be felt as judder; on a shaft it can cause vibration and wear.

  3. Feeler gauges

    Each blade is marked with its thickness, for example 0.05 mm or 0.002 in. The right blade slides into the gap with a light drag. Blades can be stacked: their thicknesses add. Blades are kept clean and lightly oiled, never forced, and replaced when kinked.

  4. Straight edge and flatness

    A precision straight edge is laid across a clean surface lengthways, crossways and diagonally. The thickest feeler blade that slides under it shows the largest gap – the distortion. The result is compared with the manufacturer's limit to decide whether the surface is acceptable.

  5. End float and clearances

    Some clearances are measured as movement rather than gaps. For crankshaft end float, a dial gauge is set against the end of the shaft; the shaft is moved fully one way and then the other, and the difference is the end float. The manufacturer's data gives the acceptable range.

  6. Errors to avoid

    • A loose or flexing mount reads its own movement.
    • A plunger at an angle reads less than the true movement.
    • Dirt under a straight edge creates a false gap.
    • Forcing a feeler blade gives a falsely large reading.
    • Temperature changes size; measure at room temperature.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Tools and measurement lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

About this lesson

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.