Ackermann steering and toe-out on turns – Motor Vehicle Theory motor mechanics lesson
Lesson 75 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Discover why the two front wheels must turn by different amounts in a corner, how the steering arms make that happen, and how to work out the angles with a little trigonometry.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
A scientific calculator with tan and inverse tan is needed for the calculations. The lesson explains steering design; checking and correcting a real car's steering is work for a trained technician. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “A forklift truck or a ride-on mower often steers with its rear wheels. Where would its turning center be, and how would its steering arms need to be angled?”
- Later: the homework, then the practice test.
Watch out for
- Thinking both front wheels should turn by the same angle. The inner wheel is on a smaller circle, so it must turn more. Equal angles would make a tire scrub sideways.
- Confusing toe-out on turns with ordinary toe. Toe is measured with the wheels straight ahead and can be adjusted. Toe-out on turns is the difference in angles during a turn and is built in by the steering arms.
- Thinking the turning center is between the front wheels. For a car steered by its front wheels, the turning center lies on the line of the rear axle, out to the side of the car.
Hands-on: On a large sheet of paper, draw a car from above to scale (for example 1 cm = 10 cm): a wheelbase of 26 cm and a track of 15 cm. Mark a turning center on the line of the rear axle, 80 cm from the car's middle (tape on extra paper if needed). Draw a line from it to each front wheel and use a protractor to draw each wheel at right angles to its line. Measure the two steering angles and compare them with the worked example. No real car is needed.
What you will learn
- I can explain why the inner front wheel must turn more sharply than the outer one.
- I can describe how angled steering arms produce the Ackermann effect.
- I can explain what toe-out on turns is and what a wrong reading suggests.
- I can calculate the steering angle of each front wheel from the wheelbase, track and turning radius.
Key words
- Ackermann steering
- A steering layout in which the inner front wheel turns through a larger angle than the outer one, so that both roll round the same turning center.
- turning center
- The single point that all the wheels should circle around in a slow turn. For a car steered by its front wheels it lies on the line of the rear axle.
- toe-out on turns
- The difference between the steering angles of the inner and outer front wheels when the car is turning. Also called the turning angle difference.
- wheelbase
- The distance from the center of the front axle to the center of the rear axle.
- track
- The distance between the centers of the left and right wheels on the same axle.
The big ideas
When a car turns a corner slowly, each wheel follows its own circle. The inner front wheel is on a smaller circle than the outer front wheel, so it must be turned more sharply. If both front wheels turned by the same angle, at least one tire would be dragged sideways, scrubbing rubber off and fighting the steering.
The answer is a layout named after Rudolph Ackermann. The steering arms on the hubs are angled inwards, so that as the steering turns, the inner wheel automatically swings through a bigger angle than the outer wheel. The difference between the two angles is called toe-out on turns.
In this lesson you will see why the geometry works, how to calculate the ideal angles, and why a technician measures toe-out on turns when checking a car that has hit a curb. Measuring and adjusting steering is work for a trained technician; this lesson explains the ideas.
Read-through: the teaching steps
Every wheel on its own circle
Picture a car turning slowly in a parking lot. Draw lines at right angles to each wheel, through its center. For the tires to roll without sliding, all those lines must meet at one point: the turning center.
The rear wheels do not steer, so the turning center must lie somewhere along the line of the rear axle. The front wheels must each point at right angles to a line drawn to that same point.
Why the inner wheel turns more
The inner front wheel is closer to the turning center than the outer front wheel. A line from a nearer point makes a steeper angle, so the inner wheel must be steered through a larger angle.
For a turning center a distance R from the middle of the rear axle, with wheelbase L and track t:
- tan (inner angle) = L ÷ (R − t/2)
- tan (outer angle) = L ÷ (R + t/2)
How the steering arms do it
Each front hub has a steering arm joined to a track rod. If the arms pointed straight back, both wheels would turn by the same angle. Instead, the arms are angled inwards. A common rule of thumb is that lines drawn along the two arms meet near the middle of the rear axle.
As the steering turns, the arm on the inner wheel swings into a position where the same movement of the track rod turns it more. The result is that the inner wheel turns more than the outer wheel – the Ackermann effect – with no extra parts.
Toe-out on turns
Because the inner wheel turns more, the fronts of the two wheels spread apart in a turn: the wheels toe out. The difference between the two angles is toe-out on turns.
A technician checks it with the front wheels on turning plates: one wheel is turned to a set angle and the angle of the other wheel is read. The manufacturer's data gives the expected reading. If the reading is wrong, a steering arm may be bent. Unlike toe, it is not normally adjusted on its own: the fix is to replace the bent part.
Real cars are not perfect
True Ackermann geometry is exact only for slow turns. At speed, tires run at small slip angles and the ideal angles change, so many road cars use only part of the full Ackermann effect, and some racing cars use even less.
The designer chooses the balance for the car's job. The key idea for this lesson is that the inner wheel turns more, and that the difference is designed in by the angle of the steering arms.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
About this lesson
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.