▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Lubrication: oil, friction and wear – Garage Basics motor mechanics lesson

Lesson 13 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out why an engine would destroy itself in minutes without oil, how a thin film of oil keeps metal parts apart, and what the oil system and its warning light do.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The activities use paper, books and a tray only. Used engine oil should never be handled without gloves; this lesson needs no oil. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think engines wear most in the first few seconds after starting from cold?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking oil only reduces friction. Oil also cools, seals, protects against rust and carries dirt to the filter.
  • Thinking thicker oil is always better. Too thick an oil flows slowly when cold, so parts are poorly protected at start-up, and it wastes energy.
  • Thinking the oil warning light means "top up soon". It means oil pressure may be low. The engine should be stopped safely and checked.

Hands-on: Friction test with household items: rub two sheets of sandpaper together, then two sheets of paper, and feel the difference. Then slide a book down a tray tilted on a few other books, measure the time, and repeat with a sheet of baking paper under the book. Compare the times. Then write the oil's journey round an engine as a flowchart. No oil or car fluids are needed.

What your child will learn

  • I can explain what friction and wear are and why they matter in an engine.
  • I can explain how a film of oil reduces friction and wear.
  • I can describe the path of oil through an engine.
  • I can explain what viscosity means and why oil grades matter.

Key words

friction
A force that resists two surfaces sliding over each other. It turns movement energy into heat.
wear
Damage caused when surfaces rub together and tiny bits are worn away.
lubricant
A substance, such as oil, that reduces friction between moving surfaces.
viscosity
How thick a liquid is: how much it resists flowing.
oil pump
The pump, driven by the engine, that pushes oil round the engine.
oil filter
A filter that removes dirt and tiny bits of metal from the oil.

The big ideas

An engine is full of metal parts sliding and spinning against each other: pistons in cylinders, the crankshaft in its bearings, the camshaft lobes pushing on the valve gear. Even surfaces that look smooth are rough under a microscope. Rubbing them together creates friction, which wastes energy as heat, and wear, which slowly destroys the parts.

Engine oil is a lubricant. Pumped between the moving parts, it forms a thin film that keeps the metal surfaces apart, so they slide on oil instead of on each other. The oil also carries heat away, helps seal the piston rings, protects against rust and carries dirt to the filter.

The owner's manual says which oil an engine needs and how often its level should be checked and the oil changed. Used engine oil is harmful to skin, so workshop staff wear gloves; the UK's Health and Safety Executive warns that frequent, prolonged contact can cause skin disorders. This lesson is about how lubrication works, not how to change oil.

Read-through: the teaching steps

  1. Friction and wear

    Under a microscope, metal surfaces have tiny peaks and valleys. When two surfaces rub, the peaks catch on each other. This friction turns kinetic energy into heat, and it breaks off tiny bits of metal: wear. In an engine, metal rubbing on dry metal would overheat and seize within minutes.

  2. The oil film

    Oil fills the gaps between moving parts. When a shaft spins in a bearing, it drags oil round with it and floats on a thin wedge of oil, thinner than a human hair. The metal surfaces no longer touch, so friction and wear are tiny. Moving parts like these are inside the engine shown in the drawing on the lesson page.

    Engine (under the hood)WindshieldWheel and tireDoorTaillightsExhaustHeadlights
    The main parts you can find on almost every car.
  3. The oil's journey

    • The oil is stored in the oil pan, under the engine.
    • The oil pump draws it up through a strainer.
    • It passes through the oil filter, which traps dirt and metal particles.
    • It flows along passages (galleries) to the crankshaft bearings, camshaft and other parts.
    • It drains back down into the oil pan, and the journey begins again.
  4. More than lubrication

    Engine oil also:

    • carries heat away from hot parts such as the pistons
    • helps the piston rings seal
    • stops metal surfaces rusting
    • holds dirt in suspension so the filter can catch it

    Over time oil breaks down and gets dirty, so the maker's service schedule says when it should be changed by a technician.

  5. Viscosity and grades

    Viscosity is how thick a liquid is. Oil gets thinner when hot and thicker when cold. Too thin, and the film breaks; too thick, and it flows slowly when cold and wastes energy. Multigrade oils, with grades such as 5W-30, behave like a thin oil when cold and a thicker oil when hot. The handbook says which grade an engine needs.

  6. The warning light

    Many cars have an oil pressure warning light. Warning lights should normally go out once the engine has started. If the oil warning light comes on while driving, the oil may not be reaching the parts, so the driver stops safely and the engine is checked before it is driven further.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.