▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Engine parts: block, head, pistons, crankshaft and camshaft – Garage Basics motor mechanics lesson

Lesson 2 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Take a tour of the main parts inside an engine – block, head, pistons, connecting rods, crankshaft and camshaft – and see how they work together to turn burning fuel into rotation.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

All the measuring can be done with card models. Engines must only ever be opened by trained technicians in a workshop. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think engine makers use belts or chains to drive the camshaft, instead of a separate motor?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the camshaft turns at the same speed as the crankshaft. Each valve opens once every two crankshaft turns, so the camshaft turns at half speed.
  • Thinking the piston travels the crank throw distance. The piston goes from one side of the throw's circle to the other, so the stroke is twice the throw.
  • Thinking the head gasket is just packing. It seals combustion pressure, coolant and oil passages; when it fails the engine can overheat or lose power.

Hands-on: Build a crank model: push a pencil through the center of a card disc (the crankshaft) and pin a card strip (the connecting rod) to a point 3 cm from the center. Fix the other end of the strip to a card "piston" that slides in a slot cut in a box. Turn the disc and measure how far the piston moves from top to bottom. Is it twice 3 cm? Then cut an egg-shaped card cam and see how it lifts a pencil "valve" once per turn.

What your child will learn

  • I can name the main parts of an engine and say what each one does.
  • I can explain how the connecting rod and crankshaft turn up-and-down motion into rotation.
  • I can explain why the camshaft turns at half the speed of the crankshaft.
  • I can relate the stroke of an engine to the throw of the crankshaft.

Key words

cylinder block
The large, strong casting that contains the cylinders. Most other engine parts bolt to it.
cylinder head
The part bolted on top of the block. It holds the valves, and on a gasoline engine the spark plugs.
piston
A metal plug that slides up and down inside a cylinder. Piston rings seal it against the cylinder wall.
connecting rod
The rod that joins a piston to the crankshaft.
crankshaft
The shaft with offset "throws" that turns the pistons' up-and-down motion into rotation.
camshaft
A shaft with egg-shaped lobes (cams) that open the valves at the right moments.

The big ideas

An engine is a set of parts that work together to turn the energy in fuel into a turning force. The biggest part is the cylinder block, which holds the cylinders. Bolted on top is the cylinder head, which holds the valves and, on a gasoline engine, the spark plugs. A gasket between them keeps the gases, coolant and oil where they belong.

Inside each cylinder a piston slides up and down. A connecting rod joins the piston to the crankshaft. The crankshaft has offset sections called throws, so when the piston is pushed down the crankshaft is forced to turn – just like your leg pushing a bicycle pedal round.

The camshaft opens the valves. It is driven from the crankshaft by a toothed belt, a chain or gears, and it turns at exactly half the crankshaft's speed, because each valve opens once in every two turns of the crankshaft. This is theory for understanding: engines are opened only by trained technicians in a workshop.

Read-through: the teaching steps

  1. The cylinder block

    The block is the backbone of the engine, usually cast from iron or aluminum. It contains the cylinders and passages for coolant and oil. Underneath is the crankcase, where the crankshaft turns. See where the engine sits in the drawing on the lesson page.

    Engine (under the hood)WindshieldWheel and tireDoorTaillightsExhaustHeadlights
    The main parts you can find on almost every car.
  2. The cylinder head and gasket

    The head closes the top of each cylinder to form the combustion chamber. It contains the inlet and exhaust ports and their valves. The head gasket is a thin seal between head and block. If it fails, gases, coolant or oil can leak between passages.

  3. Pistons and rings

    The piston takes the push of the burning gases. Piston rings sit in grooves around it: the top rings seal in the pressure, and an oil-control ring scrapes surplus oil off the cylinder wall so it is not burned.

  4. Connecting rod and crankshaft

    The connecting rod links the piston to a throw on the crankshaft. As the piston goes down, the rod pushes the throw round in a circle. The distance from the center of the crankshaft to the center of the throw is the crank throw. The piston travels twice this distance from top to bottom:

    • Stroke = 2 × crank throw
  5. The camshaft and its drive

    Each cam is egg-shaped. As it turns, the pointed part (the lobe) pushes a valve open, and a spring closes it again. The camshaft is driven by a timing belt, chain or gears. Because each valve opens once per cycle, and a cycle takes two crankshaft turns, the camshaft turns at half the crankshaft speed.

    • Camshaft speed = crankshaft speed ÷ 2
  6. The flywheel and the oil pan

    A heavy flywheel on one end of the crankshaft smooths out the pushes from the pistons. Underneath the engine, the oil pan holds the engine oil, which is pumped round to every moving part.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.