▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Reading a POH/AFM performance table – Private Pilot Theory aviation lesson

Lesson 197 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Learn where performance data sits in a flight manual and how to read a performance table – including interpolating between rows and columns.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do manufacturers print tables rather than formulas for performance?”
  4. Later: the homework, then the practice test.

Watch out for

  • Reading the nearest value instead of interpolating. Interpolate in proportion between the two printed values.
  • Interpolating the wrong way. Check the answer lies between the two printed values.
  • Using the owner's manual instead of the approved manual. The PHAK says an owner's manual cannot substitute for the approved AFM/POH.

Hands-on: Find a table of numbers – a bus timetable or tide table. Pick a time halfway between two printed times and estimate the in-between value by interpolation.

What you will learn

  • I can name the standard sections of a POH/AFM.
  • I can find the performance section.
  • I can read a value from a table.
  • I can interpolate between two values.
  • I can interpolate in two directions (double interpolation).

Key words

POH/AFM
Pilot's operating handbook / aircraft flight manual.
performance section
Section 5 of the standard manual layout.
interpolation
Finding a value between two printed values in proportion.
double interpolation
Interpolating across both rows and columns.
pressure altitude
The altitude used to enter most performance tables.

The big ideas

The PHAK (chapter 9) gives the typical layout of a flight manual: General (1), Limitations (2), Emergency Procedures (3), Normal Procedures (4), Performance (5), Weight and Balance/Equipment List (6), Systems Description (7), Handling, Service and Maintenance (8) and Supplements (9). The approved manual is specific to the aircraft, usually by serial number; an owner's manual cannot replace it.

Performance tables are usually entered with pressure altitude and temperature. When the conditions fall between printed values, the reader interpolates – assumes the value changes evenly between the two printed figures. If both the altitude and the temperature fall between rows and columns, interpolation is done in two steps (double interpolation).

The figures that come out are unfactored: the UK CAA SafetySense leaflet recommends safety factors on top (see the performance-charts lesson). This lesson teaches the arithmetic of reading tables; it is not a way to plan a real flight.

Read-through: the teaching steps

  1. Where to look

    Section 5, Performance, in the standard nine-section layout. Limitations are in section 2.

  2. Entering a table

    Find the row for pressure altitude and the column for temperature. Where they meet is the value.

  3. Single interpolation

    Value = lower + (fraction of the way across) × (upper − lower).

    1,000 ft → 400 m; 2,000 ft → 440 m. At 1,250 ft: fraction 0.25; 400 + 0.25 × 40 = 410 m.

  4. Double interpolation

    First interpolate along each row for temperature, then interpolate between those results for altitude.

  5. Sense check

    The answer must lie between the printed values around it. Higher, hotter → longer distances.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Flight Performance and Planning lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.