Lubrication and cooling – Private Pilot Theory aviation lesson
Lesson 155 of 228 in the Private Pilot Theory course (ages 16+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Learn the jobs oil does inside a piston engine, how air-cooled piston engines shed heat, and what the oil and cylinder head temperature gauges tell the pilot.
- Time
- 45 minutes + 10 min homework
- Course
- Private Pilot Theory (ages 16+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.
How to use this lesson
This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why is it hardest to keep an air-cooled piston engine cool just when it is working hardest – at take-off?”
- Later: the homework, then the practice test.
Watch out for
- Thinking oil only lubricates. It also cools, seals the rings and carries contaminants.
- Expecting oil temperature to rise straight after a cold start. The handbook notes it changes slowly and can take several minutes.
- Thinking a fast descent is always "easy" on the piston engine. High-speed descents can shock-cool the cylinders.
Hands-on: Feel the fins on a radiator or a bicycle hub, or look at a picture of a motorbike cylinder. Blow across a warm mug with and without a cardboard "baffle" guiding the air over it and compare how quickly it cools.
What you will learn
- I can list the jobs the oil does.
- I can compare wet-sump and dry-sump systems.
- I can explain how baffles, fins and cowl flaps cool an air-cooled piston engine.
- I can explain what high oil temperature might mean.
- I can explain shock cooling.
Key words
- wet sump
- An oil system where the oil is kept in a sump at the bottom of the piston engine.
- dry sump
- An oil system where oil is pumped to a separate external tank.
- baffles
- Panels that direct cooling air over the cylinders.
- cowl flaps
- Adjustable flaps on the cowling: open for more cooling, closed for less.
- CHT
- Cylinder head temperature – a direct, quick-reacting measure of cylinder temperature.
The big ideas
Oil does far more than make parts slippery. The PHAK (chapter 7) says the oil system lubricates the moving parts, reduces friction, removes heat, helps seal the piston rings against the cylinder walls and carries away contaminants. It may be held in a wet sump at the bottom of the piston engine or in a separate tank (dry sump).
Most light-aircraft piston engines are air-cooled. Air enters behind the propeller, baffles direct it over finned cylinders, and it leaves through openings at the lower rear of the cowling. Cooling is weakest on the ground, in the take-off and go-around, and at high power and low airspeed. Cowl flaps, where fitted, let the pilot open the cowling for more cooling or close it for less.
Gauges show what is happening: oil pressure, oil temperature and cylinder head temperature (CHT), each with a green normal range and red limits. High temperatures can mean power loss, extra oil use, detonation and damage. This is theory for understanding only.
Read-through: the teaching steps
The jobs of oil
From the handbook:
- lubricates moving parts and reduces friction
- removes heat
- seals the piston rings against the cylinder walls
- carries contaminants away to the filter
Wet sump and dry sump
Wet sump: oil is stored in the sump at the bottom of the piston engine. Dry sump: oil is pumped to an external tank.
Air cooling
Air enters through an inlet behind the propeller hub. Baffles direct it over the cylinder fins and other hot parts. It leaves through openings in the lower, rear cowling.
When cooling is weakest
The handbook lists ground operations, take-off, go-arounds and other high-power, low-airspeed situations. High-speed descents can do the opposite – cool the cylinders too quickly (shock cooling).
Cowl flaps
Opening cowl flaps lets more air through and lowers temperature; closing them restricts airflow and raises temperature.
Reading the gauges
- Oil pressure (psi): green normal, red minimum and maximum.
- Oil temperature: changes slowly; green normal, red maximum.
- CHT: reacts quickly; green normal, red maximum.
The handbook says high CHT can be reduced by more airspeed, a richer mixture, less power, and open cowl flaps.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.