▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Icing: types, conditions and carburetor icing – Private Pilot Theory aviation lesson

Lesson 91 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Ice can build on an airframe in cloud just below freezing, and inside a carburetor even on a warm, humid day. Learn when each kind of icing is most likely and why.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It explains why icing happens; it is not an operating guide. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might carburetor icing be more of a surprise to a pilot on a mild, damp day than on a freezing one?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking icing only happens below freezing outside. Carburetor icing can occur on warm, humid days because the carburetor cools the air by 60–70 °F.
  • Thinking the coldest cloud gives the worst airframe icing. Icing is typically worst from 0 to −15 °C; very cold cloud is not the worst case.
  • Thinking carburetor heat adds power. Warm air is less dense, so carburetor heat reduces power – by up to 15 %.

Hands-on: Put a metal spoon in the freezer for 20 minutes, then breathe on it or hold it over a cup of hot water. Watch frost or droplets form – moist air touching a cold surface. Compare with a spoon at room temperature.

What you will learn

  • I can explain what supercooled water is and why it freezes on impact.
  • I can state the temperature band in which airframe icing is typically worst.
  • I can tell apart clear ice and rime ice by how they form.
  • I can describe the temperature and humidity in which carburetor icing is most likely.
  • I can describe, in theory, the first signs of carburetor icing and the effect of carburetor heat.

Key words

supercooled water
Liquid water droplets colder than 0 °C that freeze the moment they hit something.
clear ice
Ice formed from large supercooled drops that spread before freezing; it builds quickly.
rime ice
Ice formed from smaller supercooled droplets that freeze almost at once.
carburetor icing
Ice forming inside the carburetor as fuel vaporization and the venturi's pressure drop cool the incoming air.
carburetor heat
A control that sends warmed air to the carburetor to melt or prevent ice.

The big ideas

Cloud often contains water droplets colder than 0 °C that are still liquid – supercooled water. The FAA Pilot's Handbook explains that supercooled water freezes on impact with an aircraft. The CAA's Skyway Code and the handbook agree that visible moisture at 0 °C or below can cause airframe icing, and that it is typically worst between 0 and −15 °C. The handbook says clear icing is very rapid between 0 and −15 °C, and that at high levels icing from smaller droplets may be rime or mixed ice.

Carburetor icing is different: it happens inside the piston engine's carburetor and does not need freezing outside air. As fuel vaporizes and the air speeds through the venturi, the handbook says the temperature in the carburetor can drop by 60–70 Fahrenheit degrees. So icing is most likely when the outside temperature is below about 21 °C (70 °F) with relative humidity above 80 %, but it can occur at temperatures up to about 38 °C (100 °F) with humidity as low as 50 %.

The handbook describes the first sign in an airplane with a fixed-pitch propeller as a drop in rpm; with a constant-speed propeller, a drop in manifold pressure with rpm steady. Carburetor heat sends warmed air to the carburetor, but because warm air is less dense it can reduce power by up to 15 %. This lesson explains the theory; procedures are taught by instructors.

Read-through: the teaching steps

  1. Supercooled water

    Tiny cloud droplets can stay liquid well below 0 °C. When an aircraft hits them, they freeze on impact on wings, tail, propeller and windshield.

  2. When airframe icing is worst

    • Needs visible moisture (cloud, rain, drizzle) at 0 °C or below.
    • Typically worst between 0 and −15 °C.
    • Freezing rain and freezing drizzle freeze on contact with the aircraft.
  3. Clear and rime

    • Clear ice: a glossy, transparent ice formed by the relatively slow freezing of supercooled water (FAA AC 91-74B). The handbook says clear icing is very rapid between 0 and −15 °C.
    • Rime ice: a rough, milky, opaque ice formed by the instantaneous freezing of small supercooled drops (AC 91-74B). The handbook says that at high levels icing from smaller droplets may be rime or mixed.
    • Mixed: a combination of clear and rime ice on the same surface.
  4. Why ice matters

    FAA AC 91-74B says ice significantly reduces the wing's maximum lift coefficient, drag increases steadily as ice builds up, and even a thin, rough layer on the leading edge can raise the stall speed. That is why icing conditions are treated so seriously.

  5. Carburetor icing conditions

    Fuel vaporization and the venturi's pressure drop can cool the carburetor by 60–70 °F (about 33–39 °C).

    • Most likely: outside air below about 21 °C (70 °F) with relative humidity above 80 %.
    • Possible: up to about 38 °C (100 °F) with humidity as low as 50 %.
  6. Signs and carburetor heat (theory)

    The handbook's first signs: fixed-pitch propeller – a drop in rpm; constant-speed propeller – a drop in manifold pressure with rpm unchanged. Carburetor heat supplies warmed air to melt the ice, but warm air is less dense, so it can cut power by up to 15 %. A carburetor air temperature gauge, where fitted, has a yellow arc from −15 °C to +5 °C.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Meteorology lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.