▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Secondary radar and transponder modes A, C and S – Navigation and Technology aviation lesson

Lesson 20 of 90 in the Navigation and Technology course (ages 14+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Primary radar only sees a blip. Secondary radar asks every aircraft 'Who are you, and how high?' – and a box on board answers. Find out how transponders work, why there are exactly 4,096 codes, and what Modes A, C and S each add.

Time
40 minutes + 10 min homework
Course
Navigation and Technology (ages 14+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.

How to use this lesson

Sources: FAA AIM chapter 4 sections 1 and 5 (transponders and surveillance systems). The octal counting (8 × 8 × 8 × 8) links neatly to powers and number bases in math. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Primary radar works even if an aircraft's transponder is switched off. Why might controllers still want both kinds of radar?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking primary and secondary radar are the same thing. Primary sees reflections from anything; secondary needs a transponder to reply.
  • Writing a transponder code with an 8 or 9 in it. Each digit is 0–7 only, which is why there are 4,096 codes.
  • Thinking Mode A tells the controller the aircraft's height. Mode A gives the code only. Mode C (and Mode S) add altitude.

Hands-on: Make a 'transponder' game. Each player picks a secret four-digit code using only the digits 0–7 and writes it on a card with a made-up height. The 'controller' calls out a code; only the player with that code answers with their height. Then try it with everyone answering at once – that shows why Mode S's one-at-a-time calling helps.

What you will learn

  • I can explain how secondary radar differs from primary radar.
  • I can describe what Mode A, Mode C and Mode S transponders add.
  • I can explain why there are 4,096 four-digit transponder codes.
  • I can name the special emergency codes and why they matter.

Key words

secondary surveillance radar (SSR)
Ground radar that sends an interrogation signal and receives a coded reply from an aircraft's transponder.
transponder
A radio on board that automatically replies to radar interrogations (TRANSmitter + resPONDER).
squawk
The four-digit code a transponder replies with; also the word controllers use when giving a code.
Mode C
A transponder mode that adds the aircraft's pressure altitude to its reply.
Mode S
'Selective' mode: each aircraft has its own unique 24-bit address, so the ground can talk to one aircraft at a time and exchange data.

The big ideas

Primary radar shows that something is there, but not what it is or how high it is flying. Secondary surveillance radar (SSR) solves this. The ground station sends out an interrogation signal; a box on the aircraft called a transponder hears it and automatically sends back a coded reply. The FAA's Aeronautical Information Manual (AIM) notes that these replies are much stronger than a primary radar echo, which reinforces the target on the screen and allows rapid identification.

The basic reply is a four-digit code, often called a 'squawk'. Each digit runs only from 0 to 7, which the AIM confirms gives 4,096 discrete codes, each spoken digit by digit ('two one zero two'). Controllers give each flight its own code so its label on the screen shows who it is. Mode C adds the aircraft's altitude to the reply, so the controller sees height as well as position. Mode S (S for 'selective') gives every aircraft a unique 24-bit address, so the ground can interrogate one aircraft at a time and swap extra data.

Some codes have special meanings. The AIM gives 1200 as the standard VFR code in the US unless ATC says otherwise, 7700 as the emergency code and 7500 as the hijack code, and notes that codes in the 7600 and 7700 ranges trigger special alerts in automated facilities. This lesson explains the system for understanding; it is not instruction in using it.

Read-through: the teaching steps

  1. Question and answer

    • The ground station transmits an interrogation.
    • The transponder on board hears it.
    • It replies at once with a coded signal.
    • The ground station times the reply (for range) and notes the aerial direction (for bearing).

    Unlike primary radar, this needs the aircraft to carry a working transponder.

  2. Why replies beat echoes

    A primary echo is a faint reflection. A transponder reply is a fresh, powerful transmission. That is why the AIM says replies are much stronger than primary returns – small aircraft that barely show on primary radar stand out clearly on secondary.

  3. Mode A: who are you?

    Mode A replies with a four-digit code. Each digit is 0–7 (an octal digit), so the number of codes is:

    8 × 8 × 8 × 8 = 4,096

    There is never an 8 or a 9 in a transponder code.

  4. Mode C: how high?

    Mode C adds the aircraft's pressure altitude, measured by an encoder linked to the altimeter system. The controller's screen then shows height next to the code, which is vital for keeping aircraft apart vertically.

  5. Mode S: one at a time

    Mode S gives every aircraft a unique 24-bit address. The ground can 'call' a single aircraft rather than every transponder answering at once, which reduces overlapping replies in busy airspace. It also carries extra data, and the same equipment is the basis of 1090 MHz ADS-B.

  6. Codes with special meanings

    From the FAA AIM:

    • 1200 – standard VFR code
    • 7700 – emergency
    • 7500 – hijack
    • codes in the 7600 and 7700 ranges trigger special alerts in automated facilities

    A code that triggers an alert makes the aircraft stand out on controllers' screens straight away.

Try it: read the radar

A made-up traffic screen like the ones controllers use. Read the labels and answer the questions.

Try the real thing: OpenSky Network live air traffic map (run by a non-profit) (opens in a new tab).

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Air traffic & surveillance lessons · Navigation and Technology course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.