Project: design, build and test a glider – Ground School Basics aviation lesson
Lesson 90 of 90 in the Ground School Basics course (ages 11–16)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Become an aircraft designer: build simple gliders, run fair tests, measure glide distance and use the results to improve your design – the way the Wright brothers did.
- Time
- 60 minutes + 10 min homework
- Course
- Ground School Basics (ages 11–16)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.
For parents: how to use this lesson
This project suits a hallway or school hall and needs only paper, paperclips, a tape measure and a calculator. Launch from standing height – no climbing needed. Every answer is graded straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think real gliders have such long, thin wings?”
- Later: the homework, then the practice test.
Watch out for
- Changing several things at once. Change one variable at a time, or you cannot tell what made the difference.
- Using just one launch per design. Launches vary; repeat at least five times and use the mean.
- Throwing hard to win distance. A hard throw tests your arm, not the glider. Use the same gentle launch every time.
Hands-on: Build three gliders that differ only in wing span (for example 10 cm, 15 cm and 20 cm, same paper and nose weight). Test each five times from the same height. Plot mean distance against span. Which flew furthest – and did it match the Wrights' finding about long, thin wings?
What your child will learn
- I can plan a fair test with one variable changed at a time.
- I can measure launch height and glide distance and calculate a glide ratio.
- I can use the glide angle idea: a smaller angle means a longer glide.
- I can improve a design using my results.
Key words
- glide angle
- The angle between the glider's flight path and the ground. A small glide angle means a long, flat glide.
- glide ratio
- Distance traveled forward ÷ height lost. A glide ratio of 8 means 8 m forward for every 1 m of height.
- variable
- Something you can change or measure in an experiment.
- fair test
- An experiment where only one thing is changed and everything else is kept the same.
- aspect ratio
- How long and thin a wing is: span ÷ average chord.
The big ideas
A glider has no piston or jet engine, so it is always trading height for distance. NASA's Glenn Research Center describes the glide angle – the angle between the flight path and the ground – as a measure of a glider's flying efficiency: the tangent of the angle equals the height lost divided by the distance flown, and a small glide angle means a long flight for a small loss of height. NASA also explains that a smaller glide angle goes with a higher lift-to-drag ratio.
In this project you will build paper or card gliders, launch them from a fixed height, and measure how far they go. Dividing distance by height gives a glide ratio you can compare. Change one thing at a time – wing span, wing shape, nose weight – and keep everything else the same, so you know what made the difference.
This is how the Wright brothers worked. NASA describes how their wind-tunnel tests showed that long, thin wings (high aspect ratio) performed better, and how they doubled the aspect ratio of their 1902 glider. Record your data, look for patterns, and improve your design.
Read-through: the teaching steps
Plan
Choose one variable to change (for example wing span) and decide what you will measure (glide distance). List what you will keep the same: paper type, launch height, launch method, nose weight.
Build
Make a basic glider from paper or thin card. Add a paperclip or small piece of modeling clay to the nose so it flies smoothly rather than stalling or diving. Make it symmetrical.
Launch fairly
Launch from the same height each time (for example 1.5 m, standing on the floor) with the same gentle push, indoors away from drafts. Do at least five launches per design.
Measure and calculate
Measure each distance from directly below the launch point to where the nose first touches down. Find the mean. Glide ratio = mean distance ÷ launch height.
Improve
Change one thing: longer, thinner wings (higher aspect ratio), more or less nose weight, small bends at the back of the wing (elevators). Test again and compare.
Report
Write up your aim, method, results table, graph, conclusion and an improvement. Say what was not fully fair and how you could do better.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 18 min | Not assessed, self-checked |
| Worked examples and guided practice | 12 min | Graded by Classfern |
| Independent practice (three levels) | 21 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Technology and the environment lessons · Ground School Basics course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.