▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Primary controls: ailerons, elevator and rudder – Ground School Basics aviation lesson

Lesson 12 of 90 in the Ground School Basics course (ages 11–16)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Three hinged surfaces let a pilot control an airplane in roll, pitch and yaw. Find out how deflecting a surface changes the lift on it, and meet some unusual tail designs.

Time
45 minutes + 10 min homework
Course
Ground School Basics (ages 11–16)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.

For parents: how to use this lesson

The paper-airplane test makes the effects of control surfaces easy to see. Descriptions of controls are for understanding only, not instruction. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a designer choose a T-tail or a V-tail instead of an ordinary tail?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a down-going surface pushes that part down. A down-going surface increases camber and lift, so that part is pushed up.
  • Thinking the elevator moves the whole airplane up and down like a lift. The elevator changes pitch – it rotates the airplane about the center of gravity.
  • Thinking control surfaces work the same at every speed. They are less effective at low speed and more effective at high speed, because the force depends on airspeed.

Hands-on: Make a paper airplane and cut small flaps at the back of each wing and on a small tail. Bend both wing flaps up and fly it; then one up and one down; then bend the tail flap. Record what each change does to the flight.

What your child will learn

  • I can explain how deflecting a control surface changes the lift on that part of the airplane.
  • I can describe how the ailerons, elevator and rudder each move the airplane.
  • I can explain how differential and Frise-type ailerons reduce adverse yaw.
  • I can describe a stabilator, a T-tail, a V-tail and a canard.

Key words

control surface
A hinged part of a wing or tail that moves to change the airflow and the force on that surface.
aileron
A hinged surface on the outer trailing edge of each wing; the pair move in opposite directions to roll the airplane.
elevator
A hinged surface on the trailing edge of the horizontal stabilizer that pitches the nose up or down.
rudder
A hinged surface on the trailing edge of the fin that yaws the nose left or right.
camber
The curve of a wing or tail section. Deflecting a control surface changes the camber.

The big ideas

The primary flight controls are the ailerons, the elevator and the rudder. Each is a hinged section at the back of a wing, horizontal stabilizer or fin. When a surface moves down, it increases the camber of that section and increases the lift it makes. When it moves up, it reduces the camber and the lift (or makes lift in the other direction). By changing the force on one part of the airplane, the pilot makes it rotate about its center of gravity.

In a typical light airplane, moving the control wheel or stick left or right moves the ailerons to roll the airplane; moving it forward or back moves the elevator to pitch the nose down or up; and the rudder pedals move the rudder to yaw the nose. The faster the airflow, the more effective every surface becomes.

Designers have found many ways to do the same jobs. Some airplanes have a one-piece stabilator instead of a horizontal stabilizer and elevator. A T-tail puts the horizontal stabilizer on top of the fin, above the propeller's wash. A V-tail combines elevator and rudder into two 'ruddervators'. A canard has a small horizontal surface ahead of the wing.

Read-through: the teaching steps

  1. How a control surface works

    Deflecting a surface downwards increases the camber and the angle of attack of that section, so it makes more lift. Deflecting it upwards does the opposite. The changed force acts some distance from the center of gravity, so it makes a turning moment.

  2. Ailerons: roll

    The ailerons move in opposite directions. The wing with the down-going aileron makes more lift and rises; the other wing, with the up-going aileron, makes less lift and drops. The airplane rolls about its longitudinal axis. Find them on the drawing on the lesson page.

    Aileron (roll)Aileron (roll)Elevator (pitch)Rudder on fin (yaw)
    Ailerons roll the aircraft, the elevator pitches it and the rudder yaws it.
  3. Elevator: pitch

    In theory, moving the control column back raises the elevator. That pushes the tail down, so the nose pitches up about the lateral axis. Moving it forward lowers the elevator, the tail rises and the nose pitches down.

  4. Rudder: yaw

    The rudder pedals swing the rudder left or right. The sideways force on the fin swings the tail one way and the nose the other, yawing about the vertical axis. The rudder becomes more powerful as airspeed rises.

  5. Taming adverse yaw

    • Differential ailerons – the up-going aileron moves further than the down-going one, adding drag on the lowered wing
    • Frise-type ailerons – the leading edge of the up-going aileron pokes into the airflow and adds drag
    • Coupled ailerons and rudder – linked so a little rudder is added automatically
  6. Different tails

    • Stabilator – a one-piece horizontal stabilizer that pivots as a whole
    • T-tail – the horizontal stabilizer sits on top of the fin, above the propeller wash
    • V-tail – two angled surfaces with ruddervators, doing the jobs of elevator and rudder
    • Canard – a small horizontal surface ahead of the wing

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Physics of flight lessons · Ground School Basics course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.