▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Tools in a mechanic's toolbox – Young Mechanics motor mechanics lesson

Lesson 39 of 40 in the Young Mechanics course (ages 8–11)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Open a mechanic's toolbox and meet the spanners, sockets, screwdrivers, pliers and testers inside – and find out about the safety kit a mechanic wears.

Time
35 minutes + 10 min homework
Course
Young Mechanics (ages 8–11)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

Please keep real tools for supervised use and away from vehicles. Naming tools from a household toolbox together, with the box kept closed afterwards, is a good extension. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a mechanic today needs a computer as well as spanners?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking any spanner will do if you push hard enough. A spanner that is too big slips and rounds off the corners of the nut, and can hurt your hand. It must be the exact size.
  • Thinking tighter is always better. Too much twist can break a bolt. That is why mechanics use a torque wrench and the maker's figure.

Hands-on: Draw and cut out cards for ten tools: spanner, socket, ratchet, flat screwdriver, cross-head screwdriver, pliers, soft hammer, torque wrench, multimeter and safety glasses. Sort them into groups: "turning", "gripping", "testing" and "safety". If you have a toy construction set with a toy spanner and nuts, practise matching sizes. Leave real tools and real cars to adults.

What your child will learn

  • I can name six tools a mechanic uses and say what each is for.
  • I can explain why a spanner must be the right size.
  • I can explain what a torque wrench does.
  • I can name the safety kit a mechanic wears and say why.

Key words

spanner
A tool for turning nuts and bolts. Each one fits one size.
socket
A short tube that fits over a nut and clips onto a handle (a ratchet) to turn it.
screwdriver
A tool for turning screws. The tip must match the slot in the screw head.
torque wrench
A special handle that tightens a nut or bolt to an exact amount of twist.
multimeter
A tester that measures electricity, such as volts.
PPE
Personal protective equipment: safety glasses, gloves, boots and other kit that protects a worker.

The big ideas

A car is held together by hundreds of nuts, bolts, screws and clips. A mechanic needs the right tool for each one. Using the wrong tool can damage the part or hurt the person using it.

Most toolboxes hold spanners and sockets for nuts and bolts, screwdrivers for screws, pliers for gripping, and a hammer. A mechanic also uses special tools: a torque wrench to tighten parts to exactly the right amount, a multimeter to test electrical circuits, and a computer scan tool that plugs into the car to read its messages.

Safety comes first. The Health and Safety Executive (HSE), which looks after safety at work in Britain, says most accidents in vehicle repair are slips, trips and falls, and that frequent contact with used engine oil can harm the skin. So a mechanic keeps the floor tidy, wears safety glasses, gloves and strong boots, and is trained to use every tool. Children learn the names and look, but leave real car work to qualified adults.

Read-through: the teaching steps

  1. Spanners and sockets

    Nuts and bolts have six flat sides. A spanner grips them so they can be turned. Each spanner fits only one size, marked on its side in millimetres (or in fractions of an inch on older cars). A socket is a short tube that fits over the nut and clips onto a ratchet handle, which makes turning quicker in tight places.

  2. Screwdrivers

    Screwdrivers turn screws. A flat-blade screwdriver fits a single straight slot. A cross-head screwdriver fits a cross-shaped slot. Using the wrong size slips and damages the screw head.

  3. Pliers and hammers

    Pliers grip, hold and bend things, such as clips and wires. A mechanic's hammer is often soft-faced – made of rubber or plastic – so it can tap a part into place without denting it.

  4. Measuring and tightening

    Some parts must be tightened to an exact amount of twist, called torque. Too loose and they could come undone; too tight and they could break. A torque wrench clicks when the right amount is reached. The car maker's manual gives the figure for each part.

  5. Testing tools

    A multimeter measures electricity, such as the volts in a battery. A scan tool plugs into a socket inside the car and reads messages from the car's computers, which helps a mechanic find a fault. Modern mechanics use computers as much as spanners.

  6. Safety kit and a tidy workshop

    A mechanic wears PPE (personal protective equipment):

    • Safety glasses – to protect the eyes
    • Gloves – to protect the skin from oil and sharp edges
    • Strong boots with toe caps – in case something heavy falls

    Tools go back in the box after use, and spills are cleaned up, so nobody trips or slips.

The lesson, step by step

35 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task11 minNot assessed, self-checked
Worked examples and guided practice7 minMarked by Classfern
Independent practice (three levels)8 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More History and people lessons · Young Mechanics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.