▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Motorsport engineering: an introduction – Vehicles and Technology motor mechanics lesson

Lesson 43 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Discover what motorsport engineers do – from designing parts on a computer to reading data during a race – and the science and study routes behind the job.

Time
35 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

The power-to-weight and F = m × a examples are good GCSE / high-school physics practice. Try them with your own numbers. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If you were the team's engineer, would you choose more downforce or less drag for a track with long straights and only a few corners? Why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking motorsport engineering is mostly driving fast. It is mostly design, testing, data analysis and careful checking – engineers rarely drive the car.
  • Thinking more power always means a faster car. Mass, grip and aerodynamics matter just as much. Power-to-weight is a better measure.
  • Thinking more downforce is always better. Downforce brings drag. Engineers balance cornering grip against straight-line speed for each track.

Hands-on: Build a paper or card model car and roll it down a ramp made from a book and a board. Time three runs. Then add small coins taped on top to make it heavier and time three more runs. Try a card 'wing' too. Record your results in a table and draw a bar chart – just like an engineer analysing data.

What you will learn

  • I can describe the main tasks of a motorsport engineer.
  • I can explain power-to-weight ratio and why it matters in racing.
  • I can explain how engineers use data from sensors to improve performance.
  • I can describe the study routes into motorsport engineering.

Key words

prototype
An early version of a part or vehicle, built to test a design.
telemetry
Data sent from sensors on the car to engineers, often while it is running.
downforce
A downward force made by air flowing over wings and the car's body, pressing the tyres onto the track for more grip.
power-to-weight ratio
Power divided by mass, for example kW per tonne. Higher means faster acceleration.
set-up
How a car is adjusted for a particular track and weather – for example suspension stiffness and wing angles.

The big ideas

Motorsport engineers design, build, test and improve racing vehicles. The National Careers Service describes the work as designing prototypes with specialist software, testing parts and performance in laboratories and on track, building production models, and running quality and safety checks. At race events engineers set up vehicles for the track and the weather, analyse performance data during races, and carry out 'after-tests' to look for damage.

It is a demanding, team-based job. The National Careers Service gives typical salaries of about £27,000 a year starting and £60,000 experienced, for 39 to 45 hours a week that may include evenings, weekends and bank holidays away from home. Routes in are mainly through university (a foundation degree, higher national diploma or degree – usually 2 or 3 A levels including maths and a science for a degree) or an apprenticeship (an advanced apprenticeship usually needs 5 GCSEs at grades 9 to 4 including English and maths).

Behind the glamour is a lot of physics and maths: forces, energy, materials and data. The same skills are used in road car engineering, aerospace and many other industries.

Read-through: the teaching steps

  1. Design

    Engineers design parts on a computer, using specialist software to draw them in 3D and to test how they behave under force or in airflow before anything is made. A prototype is then made and tested. Designs go round this loop – design, make, test, improve – many times.

  2. Power-to-weight

    Acceleration depends on force and mass (F = m × a). A lighter car with the same power accelerates faster. Engineers compare cars using the power-to-weight ratio:

    power-to-weight = power ÷ mass

    That is why racing cars use light, strong materials such as carbon fibre and aluminium, and why every gram is counted.

  3. Grip and downforce

    Tyres can only push the car as hard as their grip allows. Wings and the shape of the car's underside turn airflow into downforce, pressing the tyres harder onto the track and giving more grip in corners. The cost is drag – air resistance that slows the car on straights. Engineers choose a balance for each track.

  4. Data and telemetry

    Sensors on a racing car measure speeds, temperatures, pressures, suspension movement and more. Engineers analyse this data during and after a session to decide on changes to the set-up – for example softer suspension for a bumpy track, or more wing for a twisty one. Being good with spreadsheets and graphs is a big part of the job.

  5. Testing, checks and safety

    After a session engineers check the car for damage and wear. Safety checks matter enormously: a hidden crack in a part can fail at high speed. Racing teams work under strict safety procedures, with protective equipment, and everyone has a defined role in the garage. Visitors and learners stay behind the barriers and look only.

  6. Routes in

    The National Careers Service lists:

    • University – foundation degree or HND (usually 1 or 2 A levels), or a degree (usually 2 or 3 A levels, including maths and a science)
    • Apprenticeship – advanced (usually 5 GCSEs at 9 to 4 including English and maths), or higher/degree apprenticeships (4 or 5 GCSEs plus A levels)

    Career path: specialising, for example in transmissions or electronics, or moving into roles such as chief engineer, technical manager or race team manager.

The lesson, step by step

35 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task11 minNot assessed, self-checked
Worked examples and guided practice7 minMarked by Classfern
Independent practice (three levels)8 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Careers and qualifications lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.