From carburettors to computers: engine control through time – Vehicles and Technology motor mechanics lesson
Lesson 36 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Follow how engines went from a simple spray nozzle and a hand crank to electronic control modules that measure, adjust and diagnose themselves many times a second.
- Time
- 35 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
Lambda is a ratio, so it has no units. Practise one more lambda calculation with your own numbers. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Modern cars can diagnose themselves. Does that make the technician's job easier or harder? Why?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the engine warning light means the engine is about to stop. It means the self-checks found a fault that needs looking at. How urgent it is depends on the fault – the handbook and a technician advise.
- Thinking carburettors were replaced only because computers are modern. The main reasons were precise mixture control for catalytic converters, lower emissions and better fuel use.
- Thinking the ECM only controls fuel. It also sets ignition timing, runs emissions systems and diagnoses faults.
Hands-on: Draw a 'sense – decide – act' loop on paper for a petrol engine: sensors in one box (air flow, temperature, oxygen), the ECM in the middle, and injectors and spark plugs in the third box, with arrows going round. Then draw the same loop for something at home, such as a central heating thermostat. Do not open or touch any part of a real vehicle.
What you will learn
- I can explain how a carburettor mixes fuel and air, and its weaknesses.
- I can describe what an electronic control module does in a modern petrol car.
- I can explain why tighter emissions rules pushed engines towards electronic control.
- I can describe what on-board diagnostics and the engine warning light are for.
Key words
- carburettor
- A device that uses fast-moving air to draw fuel through a jet and mix it into the air going to the engine.
- fuel injection
- Spraying measured amounts of fuel under pressure, into the intake or directly into the cylinder.
- electronic control module (ECM)
- The engine's computer. It controls fuel mixture, ignition timing and emissions systems, and checks for faults.
- sensor
- A part that measures something – such as air flow, temperature or oxygen in the exhaust – and reports it to the ECM.
- three-way catalyst
- An exhaust part that cleans three pollutants at once; it works best when the fuel mixture is kept very close to the ideal.
- on-board diagnostics
- Self-checks run by the car's computer, which store fault information and can light a warning lamp.
The big ideas
Every petrol engine needs the right amount of fuel mixed with the right amount of air, and a spark at exactly the right moment. For most of the 1900s this was done mechanically. Wilhelm Maybach is credited with the spray-nozzle carburettor: air rushing into the engine sucks fuel through a small jet and breaks it into a mist. Ignition timing was set by spinning weights and springs. Starting meant turning a crank by hand, until the electric starter arrived in 1912.
Mechanical systems were clever but rough. A carburettor gives only an approximate mixture, which changes with temperature, altitude and wear. That wasted fuel and made pollution. As clean-air rules tightened and the three-way catalyst came into use, engines needed far more precise control – something only electronics could give.
Today the US Department of Energy describes a typical petrol car as having fuel injection and an electronic control module that controls the fuel mixture, ignition timing and emissions system, and also monitors the vehicle, protects the engine from abuse, and detects and troubleshoots problems. Sensors measure, the computer decides, and actuators such as injectors act – many times every second.
Read-through: the teaching steps
How a carburettor works
Air flowing into the engine passes through a narrow throat (a venturi), where it speeds up and its pressure drops. The lower pressure draws fuel out of a jet, and the fast air breaks it into droplets. A throttle valve, worked by the accelerator, controls how much mixture goes in.
It is purely mechanical – no electronics at all.
The limits of mechanical control
A carburettor cannot easily adjust for:
- a cold engine (it needs a richer mixture – a 'choke' was used)
- thinner air at altitude
- worn jets or dirt
- quick changes in demand
The result: more fuel used and more pollution than necessary, and frequent adjustment in the workshop.
Electronic fuel injection
With fuel injection, an injector sprays a measured amount of fuel under pressure. The US Department of Energy notes fuel is injected either into the intake manifold or straight into the combustion chamber. The amount is decided by the ECM using sensor readings, so the mixture can be adjusted for every situation. Direct injection lets engines use higher compression; fueleconomy.gov puts the possible efficiency gain at 2–3%.
The ECM: sense, decide, act
A modern engine works as a loop:
- Sense – sensors measure air flow, engine speed, temperatures, throttle position and oxygen left in the exhaust
- Decide – the ECM calculates fuel quantity and spark timing
- Act – injectors and the ignition system carry it out
Because the oxygen sensor reports what came out, the ECM can correct the mixture straight away. That keeps the three-way catalyst working well. The drawing on the lesson page shows the four-stroke cycle the ECM is controlling.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. Computers that check themselves
The ECM also runs self-checks. If it finds a fault, it stores information about it and can light the engine warning lamp, so a technician with a diagnostic scan tool can find the problem.
The MOT emissions test shows how precise control has become: for a petrol car with a catalyst, the MOT inspection manual expects the lambda reading (how close the mixture is to ideal) to be between 0.97 and 1.03 – no carburettor could hold the mixture that closely.
Where next?
Electronic control made many newer ideas possible: variable valve timing, turbocharging matched to small engines, cylinder deactivation and start-stop. In electric cars the same 'sense, decide, act' idea is used by the power electronics controller to manage the motor. Working on these systems takes training and the manufacturer's data – in a workshop it is done by qualified technicians.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 11 min | Not assessed, self-checked |
| Worked examples and guided practice | 7 min | Marked by Classfern |
| Independent practice (three levels) | 8 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More History of the motor car lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- Mercedes-Benz Group – Company history 1886–1920
- US Department of Energy – The history of the electric car
- US Department of Energy and EPA, fueleconomy.gov – Advanced engine technologies
- DVSA MOT inspection manual: cars and passenger vehicles – 8. Nuisance
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.