Bicycle gears: derailleurs, hubs and gear inches – Vehicles and Technology motor mechanics lesson
Lesson 22 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how derailleur and hub gears work, and use gear inches and distance per pedal turn to compare one gear with another.
- Time
- 45 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
A bicycle turned upside down on a soft mat is a safe way to explore gears. Keep fingers and loose clothing away from the chain while the pedals turn. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think racing cyclists choose many closely spaced gears, while mountain bikers choose a very wide range?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a bigger rear sprocket gives a higher gear. A bigger rear sprocket makes the ratio smaller, so it is a lower gear – easier for hills.
- Thinking more gears always means a wider range. The range depends on the smallest and largest ratios, not on how many steps there are in between.
- Thinking you must change derailleur gears while stopped. Derailleurs need the chain moving forward to shift; many hub gears can shift while stopped.
Hands-on: With an adult, turn a bicycle upside down on a soft mat. Count the teeth on a chainring and on two different rear sprockets. Mark the tyre with chalk and turn the pedals one full turn, counting how many times the wheel goes round in each gear. Keep fingers well away from the chain while turning. Then work out the gear inches for each.
What you will learn
- I can explain how a derailleur moves the chain from sprocket to sprocket.
- I can describe how a hub gear hides its gears inside the hub.
- I can calculate a gear ratio and gear inches.
- I can calculate how far a bicycle travels for one turn of the pedals.
- I can explain why low gears help on hills and high gears on the flat.
Key words
- chainring
- A toothed ring on the cranks at the front.
- cassette
- The cluster of sprockets on the rear wheel.
- derailleur
- A mechanism that pushes the chain sideways from one sprocket or chainring to another.
- hub gear
- A set of gears sealed inside the rear hub, changed by a cable or electric control.
- gear inches
- Wheel diameter in inches × chainring teeth ÷ sprocket teeth: a way to compare gears.
- development
- How far the bicycle moves for one full turn of the pedals.
The big ideas
Your legs work best within a fairly narrow range of pedalling speeds. Gears let a cyclist keep pedalling at a comfortable rate whether climbing a steep hill or riding fast on the flat. A low gear turns the wheel a little for each pedal turn, with a big turning force – good for hills. A high gear turns the wheel a lot for each pedal turn – good for speed.
There are two main systems. Derailleur gears use a chain that is pushed sideways across a cluster of sprockets at the back (and sometimes two or three chainrings at the front). Hub gears hide a set of gears inside the rear hub, sealed from dirt and water. Single-speed bikes have just one ratio.
Cyclists compare gears in "gear inches" or by the distance travelled per pedal turn. This lesson shows the maths. Looking at gears on a real bicycle is safe with an adult, as long as fingers stay well away from the chain and sprockets when anyone turns the pedals.
Read-through: the teaching steps
Ratio
gear ratio = chainring teeth ÷ sprocket teeth
With 40 teeth at the front and 20 at the back, the ratio is 2: the rear wheel turns twice for each turn of the pedals. With 40 and 40 the ratio is 1 – a very low climbing gear. The gear-pair drawing on the lesson page shows two gears meshing; a chain links two sprockets in the same way.
Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1. Derailleur gears
The rear derailleur hangs below the cassette. A cable or electric motor moves it sideways and it guides the chain onto the next sprocket while the pedals turn forward. A spring-loaded cage takes up the spare chain. A front derailleur moves the chain between chainrings. More teeth at the back = lower gear; more teeth at the front = higher gear.
Hub gears
A hub gear uses a compact set of planetary (epicyclic) gears – a central sun gear, planet gears and a ring gear – inside the rear hub. Different parts are locked or freed to give different ratios. Hub gears are sealed from rain and dirt, and many can be changed while standing still, which suits town bikes.
Gear inches
gear inches = wheel diameter (inches) × chainring teeth ÷ sprocket teeth
A 27-inch wheel with a 42-tooth chainring and 21-tooth sprocket gives 27 × 42 ÷ 21 = 54 gear inches. The name comes from the old high-wheeler bicycles: a 54-inch gear feels like riding a high-wheeler with a 54-inch front wheel.
Distance per pedal turn
distance per pedal turn = wheel circumference × ratio
A wheel 2.1 m round with a ratio of 2 moves the bicycle 4.2 m for each turn of the pedals. Cyclists call this the development.
The main parts of a bicycle. Chainline and cross-chaining
The chain runs best when it is fairly straight. Using the biggest chainring with the biggest rear sprocket (or the smallest with the smallest) bends the chain sideways – called cross-chaining. It wears the chain and sprockets faster and can be noisy, and the same ratio is usually available in a straighter combination.
Safety around chains
A turning chain and sprockets can trap fingers. Look at gears with an adult, with the bicycle held steady or turned upside down on a soft mat, and keep hands well clear while anyone turns the pedals. In the US, the Consumer Product Safety Commission requires a chain guard on bicycles with a single front sprocket.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.