▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Wiring diagrams, symbols and cable sizes – Motor Vehicle Theory motor mechanics lesson

Lesson 92 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn to read a vehicle wiring diagram, recognise the common circuit symbols, and work out why a cable must be the right size for the current it carries.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

The calculations use π and simple formulas, so a calculator helps. Reading diagrams is a core skill in college courses; nothing here asks the learner to work on a real vehicle. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Vehicle makers are trying to cut the weight and length of wiring. What could replace some of the copper, and what new problems might that bring?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a wiring diagram shows where parts are on the vehicle. Diagrams show connections, not positions. Separate location charts show where components, connectors and earth points are.
  • Thinking a higher AWG number means a thicker wire. In AWG a smaller number means a thicker wire. A 10 AWG wire is much thicker than a 20 AWG wire.
  • Choosing cable size by current alone. Length matters too: resistance rises with length, so a long run needs a bigger CSA to keep the voltage drop small.

Hands-on: Draw the symbols for a battery, fuse, switch, relay, lamp, motor, diode and earth from memory, then check them against the lesson. Next, draw a complete diagram for a horn circuit: battery, fuse, relay, horn push and horn, with the earth at the bottom of the page. Paper and pencil only; no work on a real vehicle.

What you will learn

  • I can recognise the common symbols on a vehicle wiring diagram.
  • I can follow a circuit on a diagram from the supply, through the fuse and switch, to the load and the earth.
  • I can explain how a cable's size is given and why it must suit the current and length.
  • I can calculate the cross-sectional area and resistance of a cable.

Key words

wiring diagram
A drawing that shows how the parts of a circuit are connected, using symbols rather than pictures. It does not show where the parts sit on the vehicle.
cross-sectional area (CSA)
The area of the end of the copper conductor, usually given in square millimetres (mm²). A bigger CSA carries more current with less voltage drop.
AWG
American Wire Gauge. A wire-size scale where a smaller number means a thicker wire.
loom
The bundle of cables, wrapped together, that runs round the vehicle. Also called a wiring harness.

The big ideas

A modern car may contain over a kilometre of wire. Nobody could trace a fault by following the wires themselves, so technicians use the manufacturer's wiring diagrams. These show every circuit as a set of standard symbols joined by lines, with wire colours, connector numbers and earth points labelled.

Wiring diagrams are logical, not physical. They show how current gets from the battery to each load and back, not where the parts sit in the car. Most are drawn with the supply at the top and the earth at the bottom, so current "flows down the page".

The cables themselves must be chosen carefully. Too thin a cable for its current and length wastes voltage and gets hot; too thick wastes weight and money. This lesson explains how to read the diagrams and why cable size matters; it is not a guide to altering a vehicle's wiring.

Read-through: the teaching steps

  1. Common symbols

    You will meet the same symbols again and again:

    • Battery – long and short parallel lines (long = positive).
    • Fuse – a small rectangle or an S-shaped line in a box.
    • Switch – a break in the line with a hinged contact.
    • Relay – a coil (rectangle) beside a switch, joined by a dotted line.
    • Lamp – a circle with a cross.
    • Motor – a circle with an M.
    • Resistor – a rectangle (or a zig-zag on older diagrams).
    • Diode – a triangle against a bar; current passes only in the triangle's direction.
    • Earth – a short stack of lines or a triangle pointing down.

    The drawing on the lesson page shows a simple circuit with a battery, switch and lamp.

    +12 VBatteryFuseSwitchLampReturn through the body (earth)
    A simple lighting circuit. On a car the metal body is the return path (earth).
  2. Reading a diagram

    A good method is to trace one circuit at a time:

    • Start at the supply – battery, ignition-switched feed or a fuse box output.
    • Follow through the fuse to the switch or relay that controls the load.
    • Find the load itself.
    • Follow the return to its earth point, which is usually numbered and located on a separate chart.

    Along the way, note the wire colour codes and connector pin numbers. Colour codes and abbreviations differ between manufacturers, so the key printed with the diagram is always used.

  3. How cable size is given

    Vehicle cable is made from many fine copper strands so it can bend without breaking. Its size can be given as:

    • the cross-sectional area of copper in mm² – common in Europe and the UK;
    • the number and diameter of strands, for example 14/0.30 (14 strands, each 0.30 mm across);
    • an AWG number – common in the US, where a smaller number means a thicker wire.

    The CSA of one round strand is π × d² ÷ 4, so a cable's CSA is that figure times the number of strands.

  4. Choosing the right size

    Two things limit how small a cable can be:

    • Heating. Power lost in the cable is I² × R. Too much current in too thin a cable makes it hot, which can melt the insulation and start a fire.
    • Voltage drop. Resistance rises with length, so a long run to the back of the vehicle needs a thicker cable than a short one for the same current.

    The resistance of a cable is R = ρ × L ÷ A, where ρ (rho) for copper is about 0.0172 Ω·mm² per metre, L is the length in metres and A is the CSA in mm². Starter cables are very thick because they carry hundreds of amps.

  5. Looms, connectors and protection

    Cables are bundled into looms, wrapped and clipped to the body so they cannot rub through or touch hot or moving parts. Multi-pin connectors let sections be separated in the factory and in the workshop, and weatherproof seals keep water out.

    In the MOT, wiring is a visual check. The DVSA manual treats insecure or slightly deteriorated wiring as a minor defect, wiring likely to short-circuit as major, and wiring likely to touch hot or moving parts, or with insulation posing an imminent fire risk, as dangerous.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.