Threads and fasteners: bolts, nuts, studs and grades – Motor Vehicle Theory motor mechanics lesson
Lesson 13 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn how threads are described, how bolts, nuts and studs differ, and what strength markings and locking methods tell a technician.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains threads and fasteners; strength markings are typical engineering conventions. The activity uses household fasteners and a ruler. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think designers use studs instead of bolts in some aluminium parts?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the M number gives the bolt's length. It gives the nominal diameter; length is listed separately.
- Thinking 8.8 means the bolt is 8.8 mm. 8.8 is a strength class, not a size.
- Thinking any bolt that fits can be used. Thread, length and strength grade must all match the manufacturer's specification.
Hands-on: With an adult, collect a few household nuts, bolts and screws (for example from flat-pack furniture). Use a ruler to estimate diameters and count threads over 10 mm to work out the pitch. Look for any number markings on bolt heads. Record them in a table.
What you will learn
- I can read a metric thread description such as M10 × 1.5.
- I can convert threads per inch to pitch in millimetres.
- I can describe bolts, studs, nuts, washers and locking devices.
- I can explain the meaning of property class markings such as 8.8 and 10.9.
- I can explain why some fasteners must not be reused.
Key words
- pitch
- The distance from one thread crest to the next, in millimetres.
- threads per inch (TPI)
- How many thread crests there are in one inch; used for unified (inch) threads.
- property class
- A marking such as 8.8 or 10.9 on a metric bolt that indicates its strength.
- stud
- A rod threaded at both ends, with no head.
- torque-to-yield bolt
- A bolt designed to be tightened until it stretches slightly; usually replaced, not reused.
The big ideas
A car is held together by hundreds of threaded fasteners. Each one is chosen for a reason: its diameter, its thread, its strength and the way it is locked. A technician must recognise them and follow the manufacturer's data for each, because a wrong or weakened fastener on a safety-critical part can fail.
This lesson explains how threads are described, how to read strength markings, the difference between bolts, studs and nuts, and the methods used to stop fasteners loosening. Strength markings are given here as typical engineering conventions; the exact grade and torque for any real joint always come from the manufacturer's data.
It is theory for understanding. Fasteners on brakes, steering and suspension are only ever worked on by trained technicians.
Read-through: the teaching steps
How threads are described
Metric threads are written like M10 × 1.5:
- M – ISO metric thread;
- 10 – nominal outside diameter in mm;
- 1.5 – pitch in mm.
If the pitch is left off, the standard coarse pitch is meant. Inch (unified) threads are given as threads per inch, for example 1/2-13 UNC (coarse) or 1/2-20 UNF (fine).
Pitch and TPI
To convert threads per inch to pitch: pitch (mm) = 25.4 ÷ TPI.
The pitch also tells you how far a fastener moves per turn: one full turn moves it one pitch. A fine thread moves less per turn, gives finer adjustment and resists loosening a little better; a coarse thread is quicker to fit and less likely to strip in soft metal.
Bolts, screws, studs and nuts
- Bolt – a headed fastener used with a nut, often with an unthreaded shank.
- Set screw – threaded all the way to the head.
- Stud – threaded at both ends; one end stays in the component, so repeated removal does not wear the soft metal thread.
- Nuts – plain, flanged, castellated (with a split pin) and nylon-insert types.
- Washers – plain washers spread the load; special washers seal or lock.
Strength markings
Metric bolts carry a property class on the head, such as 8.8, 10.9 or 12.9 (typical convention):
- first number × 100 ≈ tensile strength in MPa (8 → 800 MPa);
- second number × 10 ≈ yield strength as a % of tensile (8 → 80%).
Nuts carry a matching class number. A higher-grade bolt must never be replaced with a lower one.
Stopping fasteners loosening
Vibration can loosen fasteners, so designers use:
- correct tightening torque – the main defence, because a well-stretched bolt clamps firmly;
- nylon-insert (nyloc) nuts;
- castellated nuts with split pins on steering and suspension joints;
- thread-locking compounds;
- tab washers and locking plates.
The manufacturer's data says which method applies and whether parts may be reused.
Single-use fasteners
Some bolts – for example many cylinder head bolts – are torque-to-yield: tightened until they stretch slightly into their yield range, giving a very even clamping force. Once stretched, they are replaced. Nyloc nuts and split pins are usually single-use too. The manufacturer's data always decides.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Tools and measurement lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.