Thermostats, fans and temperature control – Motor Vehicle Theory motor mechanics lesson
Lesson 36 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a wax thermostat opens on its own, how the control unit decides when to run the cooling fan, and what happens when either of them fails.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains how engine temperature is controlled. Cooling systems are hot and under pressure, and electric fans can start without warning even with the engine off: work on them is for trained technicians. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think many new engines use electronically controlled thermostats and electric water pumps instead of the simple wax thermostat and belt-driven pump?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a thermostat is electrically switched. A classic wax thermostat works on its own, from the expansion of melting wax. Some modern ones add an electric heater so the control unit can open them earlier.
- Thinking that removing the thermostat would help an engine run cooler and better. Without a thermostat the engine runs too cold, wears faster, uses more fuel and pollutes more. The thermostat is there to hold the right temperature.
- Thinking an NTC sensor's resistance rises as it gets hotter. Negative temperature coefficient means resistance falls as temperature rises.
Hands-on: Wax experiment with an adult: put a few flakes of candle wax in a small foil cup and mark the level with a pen. Stand the cup in a bowl of hot water from the kettle (the adult handles the hot water) and watch the wax melt and rise above the mark. That expansion is what opens a thermostat. Then draw a flow chart of fan control: coolant temperature sensor → control unit → relay → fan motor, with a fuse in the motor circuit. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and completely cold, and keep your hands away from the fan.
What you will learn
- I can explain how a wax-pellet thermostat opens and closes.
- I can describe how a coolant temperature sensor and the control unit switch an electric fan.
- I can explain how a negative temperature coefficient (NTC) sensor changes its resistance with temperature.
- I can link a thermostat stuck open or stuck closed to its symptoms.
- I can calculate the current and power of a fan motor using Ohm's law and P = V × I.
Key words
- wax-pellet thermostat
- A valve opened by a small capsule of wax that expands strongly as it melts, pushing a pin that opens the valve.
- NTC sensor
- A temperature sensor whose electrical resistance falls as its temperature rises (negative temperature coefficient). Most coolant temperature sensors are this type.
- relay
- An electrically operated switch. A small current from the control unit switches a much larger current to a motor such as the cooling fan.
- viscous fan
- An engine-driven fan with a fluid coupling that lets it slip when cool and drive harder when the air from the radiator is hot. Found on some older and larger vehicles.
- working temperature
- The coolant temperature range the engine is designed to run at, set by the thermostat. The manufacturer's data gives the figure.
The big ideas
An engine runs best within a narrow temperature range. Too cold and it wears faster, burns fuel less completely and makes more pollution; too hot and the oil thins, parts expand and the head gasket can fail. Temperature control is the job of two main parts: the thermostat, which decides how much coolant goes through the radiator, and the fan, which decides how much air goes through it.
The classic thermostat needs no electricity at all: a pellet of wax melts and expands, pushing the valve open. Electric fans are switched by the engine control unit, which reads a coolant temperature sensor. Many modern engines add electronically heated thermostats and electric water pumps so the control unit can fine-tune the temperature.
This lesson explains how these parts work and what their faults look like. It is not a repair guide: cooling systems run hot and under pressure, and electric fans can start without warning, so work on them is for trained technicians.
Read-through: the teaching steps
Inside a wax thermostat
A wax-pellet thermostat has a small brass or copper capsule filled with a special wax, sitting in the coolant. A pin rests in the wax, and a spring holds the valve shut.
- Cold: the wax is solid and the spring keeps the valve closed.
- Warming: the wax melts. Wax expands a lot when it melts, so it pushes the pin out and the valve opens against the spring.
- Cooling: the wax shrinks and the spring closes the valve again.
The opening temperature is set by the wax mix and is often stamped on the thermostat. The manufacturer's data gives the right one for each engine.
What the thermostat controls
When the thermostat is closed, coolant circulates through the engine and bypass, missing the radiator, so the engine warms up quickly. As it opens, more coolant flows through the radiator.
It does not just snap open and shut. It opens a little at first and further as the coolant gets hotter, until it reaches the balance where the heat removed by the radiator matches the heat made by the engine. That is why the temperature gauge on most cars sits steady once warm.
Electric fans and their control
Most modern cars have one or two electric fans behind the radiator. The control unit reads the coolant temperature sensor and, when the coolant gets hot enough, switches the fan on through a relay or an electronic fan controller. Many cars have two speeds or fully variable speed.
The fan may also run when the air conditioning is on, because the air-conditioning condenser sits in front of the radiator. Fans can keep running, or start, after the engine has been switched off, so hands must be kept away.
The NTC temperature sensor
The coolant temperature sensor is usually an NTC thermistor: its resistance falls as its temperature rises. The control unit supplies a reference voltage through a fixed resistor, and the sensor and resistor share it like a potential divider. As the coolant warms and the sensor's resistance falls, the voltage at the sensor falls.
The control unit uses the reading for more than the fan: it adjusts fuel and ignition for a cold engine, and drives the temperature gauge. A faulty sensor can therefore cause poor running and wrong gauge readings, as well as fan problems.
Fan current and power
A fan motor is a heavy electrical load. Ohm's law gives the current: I = V ÷ R. Power is P = V × I.
For example, a fan motor with an effective resistance of 0.6 Ω on a 12-volt system draws 12 ÷ 0.6 = 20 A, and uses 12 × 20 = 240 W. That is why the fan is switched through a relay and protected by a fuse: the control unit's own circuit could not carry such a current. (Real motors draw a much bigger current for a moment as they start.)
A simple lighting circuit. On a car the metal body is the return path (earth). When things go wrong
Common faults and their symptoms:
- Thermostat stuck open: the engine takes a long time to warm up, the gauge reads low, the heater blows only lukewarm air and fuel use rises.
- Thermostat stuck closed: coolant cannot reach the radiator, so the engine overheats quickly, often with a hot top hose and a cool radiator.
- Fan not running: the engine overheats in slow traffic but is fine at speed, because moving air cools the radiator.
- Faulty temperature sensor: wrong gauge readings, a fan that runs all the time or never, and poor cold running.
A technician confirms the cause with tests and the manufacturer's data rather than guessing.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Cooling and lubrication lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- GOV.UK – Check your vehicle is safe to drive
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.