▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Swept volume, clearance volume and compression ratio – Motor Vehicle Theory motor mechanics lesson

Lesson 27 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn how to calculate an engine's swept volume, clearance volume and compression ratio, and why diesel engines compress much more than petrol engines.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson teaches engine volume and compression ratio calculations with example figures. The activity uses a needle-free syringe and air only. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think diesel engines are often more efficient than petrol engines?”
  4. Later: the homework, then the practice test.

Watch out for

  • Forgetting to add Vc to Vs. CR uses the total volume at BDC, Vs + Vc, divided by Vc.
  • Dividing Vs by CR to find Vc. Rearrange correctly: Vc = Vs ÷ (CR − 1).
  • Using π × d² for the area. Area = π × d² ÷ 4 (or π × r²).

Hands-on: Make a model cylinder from a clear plastic syringe (no needle) with a teacher. Pull the plunger out to the 50 mL mark and block the end with your finger; push it to 5 mL. Work out the 'compression ratio' (50 ÷ 5) and feel how the air resists. Draw the syringe at both positions and label swept and clearance volumes.

What you will learn

  • I can define swept volume, clearance volume and compression ratio.
  • I can calculate swept volume from bore and stroke.
  • I can calculate compression ratio and rearrange to find clearance volume.
  • I can explain why diesel engines need higher compression ratios.
  • I can explain how changes such as gasket thickness affect the ratio.

Key words

bore
The diameter of a cylinder.
stroke
The distance the piston travels from BDC to TDC.
swept volume (Vs)
The volume the piston sweeps: piston area × stroke.
clearance volume (Vc)
The volume left above the piston at TDC.
compression ratio
(Vs + Vc) ÷ Vc: how much the mixture is squeezed.

The big ideas

Engine size is described by its swept volume: the volume the pistons sweep through as they move from bottom dead centre to top dead centre. Add up all the cylinders and you have the engine's displacement – 1.6 litres, 2.0 litres and so on.

How much the air or mixture is squeezed matters too. The compression ratio compares the cylinder's volume with the piston at the bottom to its volume with the piston at the top. The US Department of Energy explains the key difference between engine types: a petrol engine ignites the mixture with a spark plug, while a diesel injects fuel into air that has been compressed so much that it is hot enough to ignite the fuel. That is why diesel compression ratios are much higher.

This lesson teaches the calculations. Example figures are for practice; real values come from the manufacturer's data.

Read-through: the teaching steps

  1. Swept volume

    Swept volume = piston area × stroke = π × bore² ÷ 4 × stroke.

    Work in centimetres to get cm³ (1,000 cm³ = 1 litre). Engine displacement = swept volume × number of cylinders. See the piston's travel in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. Clearance volume

    When the piston is at TDC, some space remains: the combustion chamber in the head, any recess in the piston crown and the thickness of the head gasket. This is the clearance volume, Vc.

  3. Compression ratio

    CR = (Vs + Vc) ÷ Vc.

    It is written as x:1. Example: Vs = 450 cm³, Vc = 50 cm³: CR = 500 ÷ 50 = 10:1.

    Rearranged: Vc = Vs ÷ (CR − 1).

  4. Petrol and diesel

    Typical petrol engines run compression ratios around 10:1 or a little higher; diesels are much higher, often in the high teens. A diesel needs the air to become hot enough on compression to ignite the injected fuel. A petrol engine is limited by knock – the mixture igniting by itself before the spark – so its ratio is kept lower.

  5. Why compression matters

    Higher compression generally means higher thermal efficiency: more of the fuel's energy becomes work. Low compression in one cylinder – from leaking valves, worn rings or a failed gasket – reduces power and can cause rough running. Technicians compare cylinders with compression tests, using the manufacturer's data.

  6. Changing the ratio

    Anything that changes Vc changes the ratio: a thinner gasket or a skimmed head reduces Vc and raises the ratio; a thicker gasket lowers it. This is why gasket thickness is specified and why head skimming is limited by the manufacturer.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.