Non-start faults: fuel, spark, compression and cranking – Motor Vehicle Theory motor mechanics lesson
Lesson 113 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how technicians reason through a car that will not start, by checking the four things every engine needs – cranking, spark, fuel and compression – in a logical order.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson teaches logical diagnosis of non-start faults with compression ratio and percentage calculations. Fuel and ignition systems are hazardous; all practical checks are made by trained technicians. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “A car will not start on a cold, damp morning but starts perfectly later in the day. Which of the four needs would you suspect, and what extra questions would you ask the driver?”
- Later: the homework, then the practice test.
Watch out for
- Assuming a non-start is always the battery. If the engine cranks at normal speed, the battery and starter are probably fine. Look at spark, fuel, compression and the control unit's signals.
- Checking spark, fuel and compression before reading codes and live data. A zero rpm signal while cranking or an immobiliser fault explains a non-start in seconds, and a scan tool shows them without touching the engine.
- Looking only at the actual compression numbers. Compare cylinders with each other as well as with the manufacturer's figures. One low cylinder stands out even if the numbers are unfamiliar.
Hands-on: Make a "non-start flowchart" on a large sheet of paper. Start with the question "Does it crank?" and branch to the starting system or to "What does the scan tool show?". Then add branches for spark, fuel and compression, with two possible causes under each. Test your chart on three made-up faults that a friend writes down. Paper only; no vehicle.
What you will learn
- I can separate "no crank" faults from "cranks but will not start" faults.
- I can explain the four needs of a running engine and the evidence for each.
- I can explain how the immobiliser, crankshaft sensor and fuel pump can stop an engine starting.
- I can calculate compression ratio and compare compression readings between cylinders.
Key words
- no-crank
- A fault where the starter does not turn the engine at all, or turns it very slowly.
- crank, no start
- A fault where the engine turns over normally but does not fire and run.
- compression
- The squeezing of the air (or air and fuel) in the cylinder by the piston. Low compression stops a cylinder firing properly.
- compression ratio
- The total cylinder volume with the piston at the bottom divided by the volume left with the piston at the top.
- immobiliser
- An anti-theft system that stops the engine starting unless the correct key or key fob is recognised.
The big ideas
"It won't start" is one of the most common calls a technician gets. The fastest way to the answer is not to guess but to sort the fault.
First: does the engine crank? If the starter does not turn the engine, or turns it slowly, the fault is in the starting system, the battery or the safety interlocks – covered in the starting systems lesson. If it cranks normally but will not fire, the technician asks what the engine is missing. A petrol engine needs four things: cranking speed, a spark at the right time, the right amount of fuel, and compression. A diesel needs cranking, fuel and compression, with heat from compression lighting the fuel.
Fuel and ignition systems carry serious hazards: HSE warns that petrol fires are always serious, and ignition systems produce very high voltages. This lesson explains the reasoning only; all checks on a vehicle are made by trained technicians.
Read-through: the teaching steps
Crank or no crank?
Watch and listen as the engine is cranked by a qualified person:
- No sound at all – battery, immobiliser, safety switch (clutch or park/neutral), control circuit or solenoid.
- A click or very slow cranking – battery, high-resistance cables or earth, or the starter.
- Normal cranking, no start – move on to spark, fuel and compression.
Cranking that is a little slow can also stop an engine starting, because the control unit needs a minimum speed signal and the cylinders lose compression.
Use the control unit's eyes first
Before any physical checks, a technician reads fault codes and live data with a scan tool:
- Engine speed while cranking – if it reads zero, the crankshaft position sensor or its wiring may be faulty. Without that signal, the control unit fires no spark and no injectors.
- Immobiliser status – a key not recognised may allow cranking but block fuel and spark.
- Coolant temperature – a false reading can make the mixture wrong for starting.
- Fuel rail pressure, where a sensor is fitted.
One sensor can stop both spark and fuel, so this step often finds the cause quickly.
Spark
A petrol engine needs a strong spark at each plug, at the right moment. Possible faults:
- no signal from the crankshaft sensor, so the control unit never triggers the coils;
- a failed coil or its supply;
- wet, fouled or worn spark plugs, for example after many short cold starts.
Ignition systems produce tens of thousands of volts. Checks are made by trained technicians with the right test equipment, never by holding leads.
Fuel
The engine needs the right amount of fuel, delivered at the right pressure. Possible faults:
- an empty tank or a faulty fuel gauge;
- a fuel pump that does not run – its fuse, relay, wiring, an inertia or crash cut-off, or the pump itself;
- a blocked filter or low fuel pressure;
- injectors not being triggered;
- the wrong fuel, such as petrol in a diesel.
HSE warns that most workshop fires involve petrol, and draining or opening fuel systems is specialist work. The technician uses pressure readings and live data from the manufacturer's procedure; learners never open any part of a fuel system.
Compression
Without compression the mixture cannot burn properly (and a diesel cannot heat its air enough to ignite the fuel). Causes of low compression include:
- a broken or slipped timing belt or chain, so the valves no longer open at the right time – a common cause of a sudden non-start with an unusually even, fast cranking sound;
- burnt or bent valves;
- worn piston rings or a failed head gasket.
A technician measures compression or cylinder leakage and compares every cylinder with the others and with the manufacturer's figures. Even cylinders matter as much as the actual numbers.
Diesel non-starts
Diesels have their own clues:
- Glow plugs heat the combustion chamber for cold starts; failed glow plugs make cold starting hard.
- Air in the fuel system, for example after running out of fuel, can stop the high-pressure pump working.
- Waxing of fuel in very cold weather can block the filter.
- Low compression is especially serious, because the diesel relies on the heat of compression to light the fuel.
Modern diesel injection runs at very high pressure; only trained technicians work on it.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Fault-finding lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy, Alternative Fuels Data Center – How do diesel vehicles work?
- HSE – Motor vehicle repair: fire and explosion
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.