Manual gearboxes: gear trains and ratios – Motor Vehicle Theory motor mechanics lesson
Lesson 55 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a manual gearbox uses pairs of gears to trade speed for torque, how two-shaft and three-shaft designs differ, and how to calculate ratios through a compound gear train.
- Time
- 50 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson covers gear ratios and gearbox layouts with worked calculations. It is theory only. Ratios quoted are typical engineering values, not specifications for a particular vehicle. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think many modern gearboxes have six or more gears when early cars managed with three?”
- Later: the homework, then the practice test.
Watch out for
- Writing the ratio as driver ÷ driven. Use driven ÷ driver. A reduction gear gives a ratio bigger than 1.
- Adding the ratios of a compound train. Ratios in series multiply.
- Thinking the gearbox increases power. It changes the balance of torque and speed. Power out is power in minus small losses.
Hands-on: Make two gear wheels from card using a plate and a cup as templates, marking evenly spaced "teeth" (for example 12 and 30). Pin them to a board so they touch, mark a start line, and turn the small one: count how many turns it makes for one turn of the large one and check it matches 30 ÷ 12. Then add a third card wheel between them as an idler and note the direction of the last wheel. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.
What you will learn
- I can calculate a gear ratio from tooth numbers and use it to find output speed and torque.
- I can explain how a constant-mesh gearbox selects a gear.
- I can compare two-shaft and three-shaft gearbox layouts.
- I can calculate the ratio of a compound gear train and the step between gears.
Key words
- gear ratio
- Driven teeth ÷ driver teeth. It tells you how many times the input turns for one turn of the output.
- constant mesh
- A design in which all forward gear pairs are always meshed; a gear is selected by locking one gear to its shaft.
- layshaft (countershaft)
- The extra shaft in a three-shaft gearbox that carries a cluster of gears driven by the input shaft.
- idler gear
- A gear placed between two others to reverse the direction of rotation without changing the ratio.
- overdrive
- A ratio below 1:1, so the output turns faster than the input; used for economical cruising.
The big ideas
An engine produces useful power only over a limited speed range, yet a car must move off from rest, climb hills and cruise at high speed. The gearbox solves this by offering several ratios. A low gear multiplies torque for moving off; a high gear lets the car travel fast while the engine turns at a comfortable speed.
Every ratio comes from pairs of toothed gears. When a small gear drives a larger one, the output turns more slowly but with more torque. Ignoring friction, power in equals power out, so what is gained in torque is lost in speed.
This is explanation for understanding, not a repair guide. Gearboxes are heavy, contain oil under the casing and are serviced only by trained technicians.
Read-through: the teaching steps
A pair of gears
When two gears mesh, the teeth passing the contact point per second are the same for both. So the larger gear turns more slowly.
- Gear ratio = driven teeth ÷ driver teeth.
- Output speed = input speed ÷ ratio.
- Output torque = input torque × ratio (ignoring small friction losses).
Meshing gears turn in opposite directions. The drawing on the lesson page shows a gear pair.
Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1. Compound gear trains
When drive passes through two or more pairs, multiply the ratios:
Overall ratio = (B ÷ A) × (D ÷ C)
where A drives B, and C (on the same shaft as B) drives D. An idler gear between two gears cancels out of the calculation; it only reverses the direction.
Constant mesh and selectors
In a modern manual gearbox all the forward gears are always in mesh. On one shaft the gears are fixed; on the other they spin freely on bearings. A sliding sleeve, moved by a selector fork from the gear lever, locks the chosen free gear to its shaft. Only that pair then carries the drive. Synchromesh, covered in the next lesson, matches speeds before the sleeve engages.
Three-shaft gearbox
Used with longitudinal engines and rear-wheel drive. The input shaft drives the layshaft (countershaft) through a constant-mesh pair. Gears on the layshaft drive gears on the output shaft, which is in line with the input shaft. Each indirect gear passes through two pairs, so its ratio is the constant-mesh ratio times the gear-pair ratio. Locking the input and output shafts together gives direct drive, 1:1.
Two-shaft gearbox
Used in most front-wheel drive transaxles. The input shaft drives the output shaft directly through one gear pair for each ratio. The output shaft carries a small pinion that drives the final drive gear and differential in the same casing. It is compact and simple, but there is no true direct-drive gear.
Choosing the ratios
Typical car gearboxes have five or six forward gears. First gear is often about 3.5:1 to 4:1 and top gear about 1:1 or an overdrive such as 0.8:1. The step between gears (one ratio ÷ the next) is usually larger in low gears and smaller in high gears, so the engine stays in its useful speed band after each change. Exact ratios are given in the manufacturer's data.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 15 min | Not assessed, self-checked |
| Worked examples and guided practice | 10 min | Marked by Classfern |
| Independent practice (three levels) | 16 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.