Engine oils: viscosity grades and specifications – Motor Vehicle Theory motor mechanics lesson
Lesson 38 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn what viscosity is, how to read a grade such as 5W-30, what multigrade, synthetic and additive mean, and why the manufacturer's oil specification matters as much as the grade.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains how engine oil grades and specifications work. Oil changes are for trained technicians or under supervision, and used oil must be disposed of properly: it harms skin and the environment. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think the same car model might be given a different oil grade in different countries?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the W in 5W-30 stands for weight. W stands for winter. The number before it describes how the oil behaves when cold.
- Thinking two oils with the same grade are the same quality. The grade only describes viscosity. Quality is shown by specifications such as API, ILSAC, ACEA or the car maker's approval.
- Thinking a thicker oil always protects an engine better. Oil that is too thick flows slowly at start-up, when most wear happens, and wastes fuel. Use the grade the manufacturer specifies.
Hands-on: Viscosity race with an adult: pour equal spoonfuls of three household liquids – water, cooking oil and golden syrup or honey – at the top of a tilted chopping board and time how long each takes to run 20 cm. Repeat the cooking oil and syrup after warming the jars in a bowl of warm (not hot) water. Record how warming changes the time. Do not use engine oil, new or used. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look at the oil grade and specification in the handbook.
What you will learn
- I can explain what viscosity is and how temperature changes it.
- I can interpret a multigrade SAE viscosity grade such as 0W-20 or 5W-30.
- I can explain the difference between a viscosity grade and a performance specification.
- I can describe the main additives in engine oil and what they do.
- I can calculate kinematic viscosity from dynamic viscosity and density.
Key words
- viscosity
- A fluid's resistance to flowing. Thick oil has a high viscosity; thin oil a low one.
- SAE grade
- A viscosity grade such as 5W-30, set out in a standard from SAE International. It describes how thick the oil is, not its quality.
- multigrade
- An oil that behaves like a thin oil when cold and a thicker oil when hot, shown by two numbers such as 10W-40.
- performance specification
- A quality standard the oil has been shown to meet, such as an API service category, the ILSAC standard, the European ACEA sequences or a car maker's own approval.
- viscosity index
- A number showing how much an oil's viscosity changes with temperature. A higher index means it changes less.
The big ideas
All oils get thinner as they get hotter. That is a problem for an engine: on a cold morning the oil must be thin enough to flow to the bearings at once, but at full working temperature it must still be thick enough to keep a strong film between the parts. Multigrade oils are designed to do both.
The grade printed on the bottle, such as 5W-30, describes viscosity only. Quality is described separately, by performance specifications. A manufacturer's handbook, for example, may require a particular grade and an oil certified by the American Petroleum Institute (API) or carrying the ILSAC symbol, which shows it meets current engine and emission-system protection standards. One car maker's owner's manual even specifies different grades for the same car in different markets – 0W-20 in North America and 5W-30 elsewhere – so the handbook for each vehicle is the guide.
This lesson explains the science and the labels. It is not a repair guide: oil changes are carried out by trained technicians or under supervision, and used oil must be handled and disposed of properly.
Read-through: the teaching steps
What viscosity means
Viscosity measures how much a fluid resists flowing. Honey has a high viscosity; water a low one.
Engineers use two measures:
- Dynamic viscosity (μ), in pascal seconds (Pa s), describes the force needed to slide one layer of fluid over another.
- Kinematic viscosity (ν) is dynamic viscosity divided by density: ν = μ ÷ ρ. It is measured in mm²/s (also called centistokes, cSt) and is the figure usually quoted for oils.
Viscosity falls steeply as temperature rises: a typical oil can be several times thinner at engine working temperature than when warm to the touch.
Reading a grade: 5W-30
A multigrade grade has two parts:
- The number before W (for winter) describes cold performance. The lower the number, the more easily the oil flows and is pumped when cold. 0W flows better in the cold than 10W.
- The number after the dash describes viscosity at about 100 °C, close to working temperature. A 30 is thicker when hot than a 20.
So 5W-30 is an oil that flows like a thin oil when cold and gives the viscosity of a grade 30 oil when hot. A single-grade oil, such as SAE 30, has only one number.
How multigrades work
A multigrade starts with a thin base oil, which flows well when cold. Viscosity index improvers – long polymer molecules – are added. When cold they curl up and have little effect; when hot they uncurl and thicken the oil, so it thins less than it otherwise would.
The result is an oil with a high viscosity index: its viscosity changes less with temperature. Synthetic base oils naturally have a higher viscosity index and resist breaking down at high temperature better than many mineral oils, which is why low grades such as 0W-20 are often synthetic.
Why thinner oils are specified
Thick oil takes more energy to shear, so it wastes fuel. A manufacturer's owner's manual explains that its thin 0W-20 oil reduces the fuel needed to overcome engine friction. Modern engines with tight clearances and variable valve timing are designed around these thin oils.
But thinner is not always better. An engine designed for a thicker oil can lose its bearing film if it is given oil that is too thin. That is why the grade is set by the manufacturer for each engine.
Specifications: quality, not thickness
Two oils with the same grade can be very different in quality. Performance specifications show what tests an oil has passed:
- API service categories for petrol engines are letters such as SN and SP (later letters are newer); the API certification mark shows the oil is certified.
- The ILSAC symbol shows the oil meets current engine and emission-system protection standards set for its member manufacturers.
- In Europe, ACEA sequences describe oils for different engine types, including those with particulate filters.
- Many car makers have their own approval numbers.
The handbook states both the grade and the specification required.
Additives and used oil
Base oil is only part of the bottle. Additives include:
- detergents and dispersants, which keep dirt and soot suspended so they are carried to the filter or drained with the oil;
- anti-wear additives, which form protective layers on metal where the film is thin;
- antioxidants, which slow the oil breaking down when hot;
- anti-foam agents and corrosion inhibitors.
Additives are used up and the oil collects dirt, which is why oil is changed at the intervals the manufacturer sets. Used engine oil is hazardous waste in the UK and must go to a proper disposal or recycling route, never down a drain.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Cooling and lubrication lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- Mazda owner's manual – Recommended oil
- GOV.UK / Environment Agency – Vehicle and oily wastes: how to classify
- HSE – Introduction to safe motor vehicle repair
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.