▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Electronic control units and networks: CAN bus basics – Motor Vehicle Theory motor mechanics lesson

Lesson 100 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how electronic control units read sensors and drive actuators, and how dozens of them share information over a two-wire network called the CAN bus.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson introduces vehicle networks and uses parallel resistance and simple timing calculations. It explains principles only; diagnosing networks is done by trained technicians with specialist tools. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Cars can now receive software updates over the air. What are the benefits, and what new risks does connecting a vehicle's networks to the outside world bring?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking each ECU sends messages to one particular unit. CAN messages have no destination address. Every unit receives every message and uses the ones it needs.
  • Thinking 60 Ω across the CAN wires means a fault. Two 120 Ω termination resistors in parallel give 60 Ω. That is the expected reading on a typical bus.
  • Thinking one faulty unit can only affect its own system. A unit that jams the bus, or a short in the network wiring, can stop many units communicating at once.

Hands-on: Play "CAN bus" with friends: each person is an ECU with a number (their priority). Everyone has a card with a message. When two people "talk" at once, the lower number wins and the other waits. Pass messages such as "engine speed 2,000 rpm" and decide which ECUs (instrument panel, gearbox, cooling fan) need each one. Paper and people only.

What you will learn

  • I can describe an electronic control unit as input, processing and output.
  • I can explain why vehicles use networks instead of separate wires for every signal.
  • I can describe the CAN bus: twisted pair, differential signals, termination resistors and message priority.
  • I can calculate termination resistance, bit time and message time on a CAN network.

Key words

electronic control unit (ECU)
A small computer that reads inputs from sensors and switches, decides what to do, and drives outputs such as injectors, motors and lamps.
actuator
An output device moved or switched by an ECU, such as an injector, a motor, a solenoid or a relay.
CAN bus
Controller Area Network: a two-wire network that lets ECUs share messages.
termination resistor
A resistor (typically 120 Ω) at each end of a CAN bus that stops signals reflecting back along the wires.
gateway
An ECU that links different networks in the vehicle and passes messages between them.

The big ideas

A modern car may have dozens of electronic control units. The US Department of Energy's guide to how petrol cars work describes the electronic control module as the part that controls the fuel mixture, ignition timing and emissions system, and also monitors the vehicle, protects the engine from abuse, and detects and troubleshoots problems. Other units run the gearbox, brakes, airbags, lighting, doors and the instrument panel.

These units need to share information. The engine speed is needed by the instrument cluster, the gearbox and the stability control. Running a separate wire for every signal to every unit would need miles of extra copper. Instead, the units talk over networks, the most common of which is the CAN bus.

This lesson explains how ECUs and networks work in principle. Diagnosing network faults uses a scan tool, an oscilloscope and the manufacturer's information, and is work for a trained technician.

Read-through: the teaching steps

  1. Input, processing, output

    Every ECU works the same way:

    • Inputs – sensors (temperature, pressure, speed, position) and switches send voltages or signals.
    • Processing – a microprocessor runs software and compares the inputs with stored data (maps), then decides what to do.
    • Outputs – transistors in the ECU switch actuators: injectors, ignition coils, motors, relays, lamps.

    The ECU also supplies sensors with a stable reference voltage, often 5 V, and checks that every input is within a sensible range. If one is not, it stores a fault code and may switch to a back-up ("limp-home") strategy.

  2. Why use a network?

    Without a network, every shared signal needs its own wire to every unit that uses it. With a network:

    • one pair of wires carries hundreds of different signals;
    • a sensor's reading can be shared by every unit that needs it;
    • new features can be added in software;
    • a scan tool connected to the diagnostic socket can talk to every unit.

    The cost is complexity: one network fault can affect many systems at once.

  3. The CAN bus

    CAN uses two wires, CAN-High and CAN-Low, twisted together. The signal is the difference between them (differential signalling):

    • for a "recessive" bit both wires sit at about 2.5 V;
    • for a "dominant" bit CAN-High rises (typically to about 3.5 V) and CAN-Low falls (to about 1.5 V).

    Electrical noise affects both twisted wires equally, so the difference between them is unaffected. That makes CAN very resistant to interference. High-speed CAN on engine and chassis systems typically runs at 500 kbit/s.

  4. Termination and resistance

    A 120 Ω termination resistor at each end of the main bus stops signals bouncing back from the ends. Seen from anywhere on the bus, the two resistors are in parallel:

    R = (120 × 120) ÷ (120 + 120) = 60 Ω.

    This is why a technician measuring between CAN-High and CAN-Low with the system powered down expects about 60 Ω on a typical bus. About 120 Ω suggests one termination is missing or a wire is open; a very low reading suggests a short between the wires.

  5. Messages and priority

    Each CAN message carries an identifier and up to 8 bytes of data (on classic CAN). There is no address: every unit hears every message and uses only the ones it needs.

    If two units start sending at once, the message with the lower identifier wins, because a dominant bit (0) overrides a recessive bit (1). The losing unit simply tries again. This is called arbitration, and it means urgent messages such as those from the brakes and engine can be given the highest priority.

  6. Other networks

    Vehicles use several networks, linked by a gateway:

    • High-speed CAN – engine, gearbox, brakes.
    • Lower-speed CAN – body and comfort systems.
    • LIN – a single-wire, slow, cheap network for simple devices such as window switches and mirror motors.
    • FlexRay and automotive Ethernet – faster networks for advanced driver assistance and cameras.

    The diagnostic socket connects a scan tool to these networks through the gateway.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.