▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Disc brakes: calipers, pads and discs – Motor Vehicle Theory motor mechanics lesson

Lesson 66 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how disc brakes are built, how sliding and fixed calipers clamp the pads, why discs are ventilated, and how to calculate the braking torque a disc brake makes.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains disc brake design and braking torque. It is theory only: brakes are safety-critical, brake dust can be harmful, and all brake work is for trained technicians. The inspection details are dated November 2026. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think many cheaper cars still use drum brakes at the rear but discs at the front?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a sliding caliper only brakes on one side of the disc. The body slides, so the outer pad is pulled on with the same force.
  • Using one friction face in the torque formula. There is a pad on each side: two faces.
  • Thinking pads are pulled back by springs. The piston seal draws the piston back a tiny distance.

Hands-on: Look closely at a bicycle with disc or rim brakes, with an adult: find the parts that clamp, the part that turns, and how the cable or hose works them, without taking anything apart. Then draw a labelled cross-section of a sliding caliper and show with arrows how the body slides. If you look at a real car's brakes through the wheel spokes, do it only with a qualified adult, with the car parked, switched off and the brakes cold, and only look.

What you will learn

  • I can name the parts of a disc brake and say what each does.
  • I can compare sliding and fixed calipers, and solid and ventilated discs.
  • I can calculate braking torque and road braking force.
  • I can explain why pad wear and brake dust matter.

Key words

brake disc
A cast-iron disc that turns with the wheel; the pads clamp onto it.
caliper
The housing with hydraulic pistons that holds the pads and clamps them onto the disc.
brake pad
A steel backing plate with a block of friction material.
sliding caliper
A caliper with pistons on one side that slides on pins to clamp both pads.
ventilated disc
A disc made of two faces joined by vanes so air can flow through and cool it.

The big ideas

This is explanation for understanding, not a repair guide. Brakes are safety-critical: only trained technicians work on them.

Nearly every modern car has disc brakes at the front, and many have them at the rear too. A disc turns with the wheel; a caliper fixed to the suspension clamps a pad onto each side. Because the disc is open to the air, it cools quickly and resists fade better than a drum.

The MOT inspection manual (section 1, as of November 2026) checks the condition of pads and discs: a pad worn below 1.5 mm is a Dangerous defect, and a disc that is significantly and obviously worn, or contaminated with oil or grease, is a Major defect.

Read-through: the teaching steps

  1. The parts

    • Brake disc: cast iron, bolted to the hub, turns with the wheel.
    • Caliper: holds the pads and contains one or more hydraulic pistons.
    • Pads: friction material bonded to a steel backing plate.
    • Carrier (on sliding calipers): bolted to the hub carrier; the caliper slides on its pins.

    The drawing on the lesson page shows a disc brake.

    CaliperBrake discFluidPistonPadsDisc (edge on)
    A disc brake: fluid pressure pushes the piston, the pads squeeze the spinning disc, and friction turns movement into heat.
  2. Sliding and fixed calipers

    • Sliding (floating) caliper: piston(s) on the inner side only. The piston pushes the inner pad; the reaction slides the caliper body and pulls the outer pad on. It is compact, light and cheap.
    • Fixed caliper: pistons on both sides; the body does not move. It gives even clamping and a stiff feel, so it suits high-performance cars.
  3. Releasing the pads

    There is no spring to pull the pads back. A square-section seal grips the piston and twists slightly as the piston moves out. When pressure is released, the seal untwists and draws the piston back a fraction of a millimetre, so the pads barely touch. As pads wear, the piston simply sits further out, so disc brakes adjust themselves.

  4. Discs and heat

    Solid discs are used where braking loads are lower, often at the rear. Ventilated discs have two faces joined by vanes; air is pumped through as they turn, carrying heat away. Some discs are drilled or slotted to help clear gases and water. Very hot discs can distort, which may be felt as a pulsing pedal.

  5. Braking torque

    Each pad face makes a friction force μ × F at the effective radius r of the pads. With two faces:

    T = 2 × μ × F × r

    The force at the road = T ÷ tyre rolling radius. A larger disc (bigger r) gives more torque from the same clamping force, which is why powerful cars have big discs.

  6. Wear and dust

    Pads wear and must be replaced before they are too thin. Wear indicators may squeal or light a warning. In the MOT, a pad worn to its wear indicator is a Major defect; an illuminated wear indicator on its own is not a reason for failure. The HSE warns that brake linings on older cars may contain asbestos, so brake dust is never blown with an airline. Learners must not touch brake parts.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.