Diesel aftertreatment: DPF, SCR and diesel exhaust fluid – Motor Vehicle Theory motor mechanics lesson
Lesson 49 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Follow diesel exhaust through the oxidation catalyst, the particulate filter and the selective catalytic reduction system, and find out how soot is burnt off and how diesel exhaust fluid turns NOx into nitrogen and water.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains diesel exhaust aftertreatment. These parts reach very high temperatures, especially during regeneration, and work on them is for trained technicians. Inspection values quoted are dated November 2026. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Some drivers who only make short trips have problems with diesel particulate filters. What advice might a car maker give, and what does that tell you about choosing the right engine for the right use?”
- Later: the homework, then the practice test.
Watch out for
- Thinking diesel exhaust fluid is a fuel additive. It is never added to the fuel. It goes into its own tank and is sprayed into the exhaust ahead of the SCR catalyst.
- Thinking a particulate filter never needs anything once fitted. Soot must be burnt off by regeneration. Lots of short trips can stop regeneration finishing, which is why the car may warn the driver.
- Thinking SCR removes soot. SCR deals with NOx. The particulate filter deals with soot.
Hands-on: Wall-flow filter model with an adult: roll several paper straws, block alternate ends with a little modelling clay, and wrap them together in a bundle around a coffee filter paper so that air blown in one end must pass through the paper. Sprinkle a pinch of cocoa powder in the inlet end and blow gently: the powder stays behind on the paper. Then draw the full aftertreatment chain in order and label what each part removes. Never touch a real exhaust or filter: they get extremely hot, especially during regeneration.
What you will learn
- I can name the parts of a modern diesel aftertreatment system in order and say what each removes.
- I can explain how a diesel particulate filter traps soot and how regeneration cleans it.
- I can explain how selective catalytic reduction uses diesel exhaust fluid to reduce NOx.
- I can explain why a three-way catalyst cannot be used to remove NOx from a diesel.
- I can calculate filter efficiency and diesel exhaust fluid use.
Key words
- diesel oxidation catalyst (DOC)
- A catalyst that oxidises carbon monoxide and hydrocarbons in diesel exhaust, and helps the later stages work.
- diesel particulate filter (DPF)
- A filter in the exhaust that captures particulate matter (soot).
- regeneration
- Burning the trapped soot in a particulate filter so that it becomes carbon dioxide and the filter is cleared.
- selective catalytic reduction (SCR)
- A catalyst system that converts NOx into nitrogen and water using ammonia made from diesel exhaust fluid.
- diesel exhaust fluid (DEF)
- A solution of urea in water, stored in its own tank and sprayed into the exhaust ahead of the SCR catalyst.
The big ideas
Diesels are efficient, but their exhaust brings two hard problems: soot (particulate matter) and oxides of nitrogen. Because a diesel always runs with spare oxygen, a three-way catalyst cannot remove its NOx. So diesels carry their own chain of aftertreatment.
The US Department of Energy lists the parts: a diesel oxidation catalyst; a diesel particulate filter, which captures particulate matter; and selective catalytic reduction, which converts NOx to nitrogen and water using diesel exhaust fluid – an aqueous urea solution held in a separate DEF tank.
The filter must be cleaned by burning off its soot from time to time, and the SCR system must be kept supplied with fluid. This lesson explains how the system works. It is not a repair guide: aftertreatment parts reach very high temperatures, especially during regeneration, and work on them is for trained technicians.
Read-through: the teaching steps
The order of the parts
In a typical modern diesel car the exhaust passes, in order, through:
- the diesel oxidation catalyst (DOC);
- the diesel particulate filter (DPF), sometimes combined with the SCR catalyst in one unit;
- the diesel exhaust fluid injector;
- the SCR catalyst, often followed by a small clean-up catalyst that stops leftover ammonia escaping.
Temperature and pressure sensors along the way, and a NOx sensor, tell the control unit what is happening.
The oxidation catalyst
The DOC works like the oxidation part of a petrol catalyst. With plenty of oxygen, it oxidises carbon monoxide to carbon dioxide and hydrocarbons to carbon dioxide and water.
It has two more jobs. It turns some nitric oxide (NO) into nitrogen dioxide (NO₂), which helps burn soot in the filter and helps the SCR reaction. And during active regeneration, fuel that reaches it is burnt on its surface, heating the exhaust going into the filter.
Trapping soot: the particulate filter
A DPF is a ceramic honeycomb whose channels are blocked at alternate ends. Exhaust enters a channel that is closed at the far end, so it must pass through the porous wall into the next channel to escape. The soot is left behind on the wall.
The filter traps the vast majority of the particles. As soot builds up, it becomes harder for exhaust to get through, so the pressure difference across the filter rises. The control unit measures that difference to estimate how full the filter is.
Regeneration
Trapped soot is carbon, and carbon burns. Regeneration burns it to carbon dioxide:
- Passive regeneration happens on its own during long, fast journeys, when the exhaust is hot and NO₂ from the DOC slowly burns the soot.
- Active regeneration is started by the control unit when the filter is getting full: it adds late post-injections of fuel, which burn in the DOC and raise the filter's temperature high enough to burn the soot quickly.
If a car makes only short trips, regeneration may not finish, and a warning light shows. The handbook explains what the driver should do. Ash from oil additives does not burn, so over a very long life a filter slowly fills with ash.
Selective catalytic reduction
Diesel exhaust fluid is a solution of urea in water – about one-third urea. It is sprayed into the hot exhaust, where the urea breaks down to ammonia:
(NH₂)₂CO + H₂O → 2NH₃ + CO₂
On the SCR catalyst, the ammonia reacts with NOx and turns it into nitrogen and water, for example:
4NO + 4NH₃ + O₂ → 4N₂ + 6H₂O
The control unit doses just enough fluid using the NOx sensors: too little leaves NOx; too much lets ammonia escape. It is called selective because the ammonia reacts with NOx rather than simply burning in the spare oxygen.
Living with the system, and the MOT
Diesel exhaust fluid is used up as the car is driven, so the tank needs topping up at intervals; the car warns the driver well before it runs out, and the handbook explains the procedure. Fluid must never be put in the fuel tank, and diesel must never go in the fluid tank.
In the MOT (inspection manual section 8, November 2026), any visible smoke from a diesel fitted with a particulate filter is a major defect, and diesel cars first used on or after 1 January 2014 have a smoke opacity limit of 0.7 m⁻¹. Removing a particulate filter therefore fails the test. Tests are done by trained MOT testers.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do diesel vehicles work?
- DVSA MOT inspection manual: cars and passenger vehicles – 8. Nuisance
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.