▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Cooling system layout and components – Motor Vehicle Theory motor mechanics lesson

Lesson 34 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Follow the coolant round an engine – water jacket, pump, thermostat, radiator, fan, expansion tank and heater – and work out how much heat the system carries away.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains how an engine cooling system is laid out. A hot cooling system is under pressure and can scald, and electric fans can start without warning: work on it is for trained technicians. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Electric cars have no engine to cool, yet many still have a coolant system. What do you think it is used for?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the cooling system's job is to make the engine as cold as possible. A cold engine wears faster, uses more fuel and makes more pollution. The thermostat holds it at its best working temperature.
  • Thinking the fan always runs when the engine runs. On most modern cars an electric fan switches on only when the coolant is hot, and it can start even with the engine off.
  • Thinking the coolant level should be checked by opening the radiator cap while the engine is warm. The level is read on the expansion tank marks, and handbooks say to check only when the engine is cold. A hot system is under pressure and can scald.

Hands-on: Draw a large labelled diagram of the cooling circuit: water pump, water jacket, cylinder head, thermostat, top hose, radiator, bottom hose, fan, expansion tank, heater matrix and bypass. Use one colour for the cold-engine path and another for the hot-engine path. With an adult, feel how the fins on a radiator-style room heater make it warm the air, and compare with a flat panel. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and completely cold, and only look – for example at the expansion tank's min and max marks.

What you will learn

  • I can explain why an engine needs a cooling system and where its waste heat comes from.
  • I can name the main parts of a liquid cooling system and describe what each one does.
  • I can trace the path of the coolant when the engine is cold and when it is hot.
  • I can use Q = m × c × ΔT to calculate the heat carried by flowing coolant.
  • I can explain why a hot cooling system must never be opened.

Key words

water jacket
Passages cast into the cylinder block and head that the coolant flows through, around the hot cylinders and combustion chambers.
water pump
A pump, usually driven by a belt or electrically, that circulates coolant round the engine and radiator.
radiator
A heat exchanger at the front of the vehicle where heat passes from the coolant to the air flowing through it.
thermostat
A temperature-operated valve that keeps coolant away from the radiator until the engine reaches its working temperature.
expansion tank
A reservoir that takes up coolant as it expands when hot and returns it as it cools. Coolant level is checked here.
heater matrix
A small radiator behind the dashboard that uses hot coolant to warm the air for the cabin.

The big ideas

Most of the energy in fuel does not end up moving the car. The US Department of Energy (Fact of the Week 709) estimates that thermal losses – heat carried away by the cooling system and the exhaust – account for about 60% of a petrol engine's fuel energy in combined driving. If that heat were not removed, the cylinder walls, pistons and oil would overheat within minutes.

A liquid cooling system pumps coolant through passages around the cylinders, carries the heat to a radiator, and lets the air carry it away. A thermostat keeps the engine at its best working temperature: warm enough to run efficiently and cleanly, cool enough to protect the metal and the oil.

GOV.UK advises drivers to check the coolant level regularly, with the vehicle handbook saying how often. This lesson explains how the system is laid out and how it works. It is not a repair guide: a hot cooling system is under pressure and can cause serious scalds, and work on it is for trained technicians.

Read-through: the teaching steps

  1. Where the heat comes from

    Combustion gases can be far hotter than the melting point of aluminium for a moment. Heat flows from the gas into the cylinder walls, the cylinder head and the pistons. Friction adds more.

    The cooling system has two jobs: remove enough heat to protect the engine, and not remove too much, because a cold engine wears faster, uses more fuel and makes more pollution. That second job is why the system has a thermostat.

  2. The coolant circuit

    Follow the coolant round:

    • The water pump pushes coolant into the water jacket in the block.
    • It flows up through the head, picking up heat around the combustion chambers and exhaust ports.
    • It leaves the head through the thermostat housing.
    • When hot, it passes through the top hose to the radiator, gives up heat to the air, and returns through the bottom hose to the pump.
    • Some coolant also flows through the heater matrix to warm the cabin.
  3. Cold engine: the bypass

    When the engine is cold, the thermostat is closed. Coolant cannot reach the radiator, so it circulates through a bypass passage back to the pump, and round the heater. The engine warms up quickly because the heat is not being thrown away.

    As the coolant reaches working temperature, the thermostat opens and coolant starts to flow through the radiator. The thermostat opens further as the temperature rises, balancing the heat made with the heat removed.

  4. Radiator and fan

    A radiator is made of many thin tubes joined by thin metal fins. The fins give a very large surface area, so heat passes easily from the coolant to the air. Most modern radiators are aluminium.

    When the car is moving, air is pushed through the radiator. In slow traffic or when parked, a fan pulls air through. On most cars the fan is electric and is switched on by the control unit using a coolant temperature sensor. Electric fans can start even after the engine is switched off – one reason to keep hands well away.

  5. Expansion tank and pressure cap

    Coolant expands as it heats up. The expansion tank, a translucent plastic reservoir with minimum and maximum marks, takes the extra volume and gives it back as the engine cools.

    The system is sealed with a pressure cap, so it runs above atmospheric pressure when hot. Higher pressure raises the coolant's boiling point, so it can run hotter without boiling. The next lesson looks at coolant and pressure caps in detail. Because the hot system is under pressure, opening the cap can release a jet of scalding coolant: it is never opened hot.

  6. How much heat does the coolant carry?

    The heat carried each second by flowing coolant is:

    Q = m × c × ΔT

    where m is the mass flow rate (kg/s), c is the specific heat capacity of the coolant (water is about 4.2 kJ/kg K; a water–antifreeze mix is a little lower), and ΔT is the temperature drop across the radiator. With m in kg/s and c in kJ/kg K, Q comes out in kJ/s, which is kilowatts.

    For example, 1.5 kg/s of water cooling by 8 K across the radiator carries 1.5 × 4.2 × 8 = 50.4 kW.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Cooling and lubrication lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.