Air–fuel ratio, lambda and mixture strength – Motor Vehicle Theory motor mechanics lesson
Lesson 40 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out why an engine needs air and fuel in the right proportions, how air–fuel ratio and lambda describe a mixture, and why most petrol engines are held at lambda 1.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains mixture strength and lambda as theory. Fuel systems are hazardous and work on them is for trained technicians only. The inspection values quoted are dated November 2026; check the official source before relying on them. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “A sports car engine is set to run slightly rich at full power. What does it gain and what does it give up?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a higher air–fuel ratio means a richer mixture. A higher AFR means more air for each kilogram of fuel, so the mixture is leaner. Rich means less air per kilogram of fuel.
- Thinking air–fuel ratio is measured by volume. It is a ratio of masses. By volume, the air would be thousands of times bigger than the fuel.
- Thinking an engine should always run as lean as possible to save fuel. Very lean mixtures misfire and raise NOx, and a three-way catalyst only cleans all three pollutants near λ = 1.
Hands-on: Mixture model with counters: let red counters be fuel and blue counters be oxygen. Suppose (as a simplified model) every red counter needs exactly three blue counters to 'burn'. Put out 4 red and 12 blue (λ = 1), 4 red and 9 blue (rich) and 4 red and 15 blue (lean). For each, count what is left over and what pollutant it stands for: unburnt fuel and carbon monoxide when rich, spare oxygen and NOx when lean. Then calculate a 'lambda' for each set as (blue ÷ red) ÷ 3. No real fuel is used in this activity.
What you will learn
- I can define air–fuel ratio and stoichiometric ratio.
- I can calculate lambda from an air–fuel ratio and say whether a mixture is rich or lean.
- I can explain why a petrol engine with a three-way catalyst is held close to lambda 1.
- I can describe how mixture strength affects power, economy and emissions.
- I can calculate the mass of fuel needed for a given mass of air.
Key words
- air–fuel ratio (AFR)
- The mass of air divided by the mass of fuel in a mixture. 14.7:1 means 14.7 kg of air for every 1 kg of fuel.
- stoichiometric ratio
- The air–fuel ratio at which there is exactly enough oxygen to burn all the fuel, with none left over. For petrol it is about 14.7:1.
- lambda (λ)
- The actual air–fuel ratio divided by the stoichiometric ratio. λ = 1 is stoichiometric.
- rich mixture
- A mixture with more fuel than the stoichiometric amount: λ is less than 1.
- lean mixture
- A mixture with less fuel (more air) than the stoichiometric amount: λ is greater than 1. Also called weak.
The big ideas
Fuel can only burn with oxygen, and the oxygen comes from the air. For each kilogram of petrol, a certain mass of air is needed to burn it completely: about 14.7 kg. That is the stoichiometric (chemically correct) ratio. Diesel's is similar, roughly 14.5:1.
If there is more fuel than that, the mixture is rich: some fuel cannot find oxygen, so carbon monoxide and unburnt hydrocarbons come out of the exhaust. If there is less fuel, the mixture is lean: there is spare oxygen, combustion can be hotter, and oxides of nitrogen rise; very lean mixtures misfire.
The US Department of Energy notes that the engine's electronic control module controls the fuel mixture. In a petrol engine with a three-way catalyst it holds the mixture very close to stoichiometric, because that is the only window in which the catalyst can clean up all three main pollutants at once. Engineers describe that window with one number: lambda. This lesson explains the theory. It is not a repair guide: fuel systems are for trained technicians only.
Read-through: the teaching steps
Air–fuel ratio by mass
Air–fuel ratio is always a ratio of masses, not volumes:
AFR = mass of air ÷ mass of fuel.
Air is very light compared with liquid fuel, so the volume of air is enormous. At about 1.2 kg per cubic metre, the 14.7 kg of air needed for 1 kg of petrol fills over 12 cubic metres – roughly the inside of a small room. An engine therefore moves far more air than fuel.
Lambda
Different fuels have different stoichiometric ratios, so engineers use lambda, which works for any fuel:
λ = actual AFR ÷ stoichiometric AFR.
- λ = 1: stoichiometric.
- λ less than 1: rich (too much fuel). For petrol, an AFR of 13.2:1 gives λ = 13.2 ÷ 14.7 = 0.90.
- λ greater than 1: lean (too much air). An AFR of 16.2:1 gives λ = 16.2 ÷ 14.7 = 1.10.
Mixture, power and economy
Typical behaviour of a petrol engine:
- Slightly rich (around λ 0.85 to 0.9) tends to give the most power, because all the oxygen is used, and the extra fuel helps cool the combustion chamber under heavy load.
- Slightly lean (around λ 1.05 to 1.1) tends to give the best economy, but NOx is high.
- Very lean mixtures burn slowly and misfire.
- λ = 1 is the compromise used almost all the time in modern petrol cars, because of the catalyst.
These are typical values; each engine's figures come from the manufacturer's calibration.
Why lambda 1 matters for the catalyst
A three-way catalyst does two opposite jobs at once: it oxidises carbon monoxide and hydrocarbons (which needs oxygen), and it reduces oxides of nitrogen (which needs a shortage of oxygen). Both can happen well only in a narrow band around λ = 1.
The control unit uses an oxygen (lambda) sensor in the exhaust to check the mixture many times a second, and trims the fuel to swing it just either side of λ = 1. A later lesson looks at catalysts and oxygen sensors in detail.
Diesels are different
A diesel controls power by the amount of fuel injected and lets air in freely, so it usually runs lean overall – often well above λ = 1, especially at light load. It cannot use a three-way catalyst for NOx, because there is always spare oxygen, so it uses other aftertreatment, such as selective catalytic reduction.
If a diesel is given too much fuel for the air available, it makes black smoke: that is a local rich mixture.
Lambda in the MOT
The MOT emissions check (inspection manual section 8, as of November 2026) tests petrol cars with a catalyst for lambda as well as gases. In the basic test, lambda must be between 0.97 and 1.03, carbon monoxide must be no more than 0.2% at fast idle (2,500 to 3,000 rpm) and 0.3% at normal idle, and hydrocarbons no more than 200 ppm at fast idle. These values show how tightly the mixture is controlled.
The test is carried out by a trained MOT tester with a gas analyser.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy, Alternative Fuels Data Center – How do diesel vehicles work?
- DVSA MOT inspection manual: cars and passenger vehicles – 8. Nuisance
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.