▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

The spark: how ignition works – Garage Basics motor mechanics lesson

Lesson 9 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how a 12-volt car battery can make a spark of many thousands of volts, why the spark happens before the piston reaches the top, and how the engine's computer times it.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

This lesson links with GCSE physics on transformers. Car ignition systems carry dangerous voltages and should never be touched; any practical demonstration should use a school low-voltage kit under a teacher's supervision. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think modern engines often have one ignition coil for each spark plug instead of one shared coil?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the battery's 12 volts goes straight to the spark plug. 12 volts could not jump the gap. The coil raises it to many thousands of volts.
  • Thinking the spark happens at top dead centre. It happens a little before TDC, because the mixture needs time to burn.
  • Thinking a transformer works on steady current. Induction needs a changing magnetic field. The coil makes its high voltage at the moment the primary current is switched off.

Hands-on: Make a "timing" demonstration: draw a crankshaft circle with TDC at the top and mark 10° and 30° before TDC. Imagine the flame needs a fixed time to burn. Roll a coin round the circle slowly, then quickly, and discuss why the spark must start earlier when the engine turns faster. If your school has a science kit, an adult can show a simple transformer demonstration with a low-voltage power supply.

What your child will learn

  • I can describe the parts of a petrol engine's ignition system.
  • I can explain how an ignition coil uses electromagnetic induction to make a high voltage.
  • I can use a turns ratio to calculate a coil's output voltage.
  • I can explain why the spark is timed before top dead centre and why timing changes with engine speed.

Key words

ignition coil
A type of transformer that turns the car's low voltage into the very high voltage needed for a spark.
spark plug
The part screwed into the cylinder head where the spark jumps across a small gap to ignite the mixture.
electromagnetic induction
Making a voltage in a wire by changing the magnetic field around it.
turns ratio
The number of turns of wire on the secondary coil divided by the number on the primary coil.
ignition timing
When the spark happens, measured in degrees before top dead centre (BTDC).

The big ideas

In a petrol engine the compressed mixture of fuel and air must be lit at exactly the right moment. That is the job of the ignition system. The US Department of Energy explains that in a petrol car the mixture is ignited by the spark plug, and the electronic control module controls the ignition timing.

A car's electrical system runs at about 12 volts, but air is a good insulator: making a spark jump a gap of about a millimetre in highly compressed gas needs many thousands of volts. The ignition coil makes this high voltage using electromagnetic induction. When the current in the coil's primary winding is switched off, its magnetic field collapses very quickly, and a huge voltage is induced in the secondary winding, which has many more turns.

The mixture takes a short time to burn, so the spark is timed a little before the piston reaches top dead centre. The engine's computer adjusts this timing constantly. Ignition systems use very high voltages, so they are worked on only by trained technicians; this lesson is theory.

Read-through: the teaching steps

  1. The parts

    • Battery – supplies about 12 volts
    • Engine control module – decides when each spark should happen
    • Ignition coil – makes the high voltage (many modern engines have one coil on top of each spark plug)
    • Spark plug – makes the spark inside the cylinder

    The spark happens at the start of the power stroke in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. The spark plug

    A spark plug has a central electrode, surrounded by a ceramic insulator, and a side electrode a small distance away. The high voltage makes a spark jump across the gap between them. The spark heats a tiny amount of mixture so much that it starts to burn, and the flame spreads through the whole chamber.

  3. How the coil works

    The coil has two windings on an iron core: a primary with a few hundred turns and a secondary with many thousands. Current flows through the primary and builds up a magnetic field. When the ECM switches the current off, the field collapses very quickly. The changing field induces a few hundred volts in the primary – and, because the secondary has about 100 times as many turns, tens of thousands of volts in the secondary.

  4. The turns ratio

    For a transformer:

    secondary voltage = primary voltage × (secondary turns ÷ primary turns)

    If the primary has 200 turns, the secondary 20,000 turns, and 300 V is induced in the primary, the secondary voltage = 300 × (20,000 ÷ 200) = 300 × 100 = 30,000 V.

  5. Timing the spark

    Burning the mixture takes a little time. If the spark happened exactly at top dead centre, the piston would already be moving down before the pressure peaked, wasting energy. So the spark is timed before TDC, for example 10° BTDC. At higher engine speeds the piston moves faster, so the spark must come even earlier: this is called advance.

  6. Too early or too late

    If the spark comes too early, the pressure rises while the piston is still coming up, which can cause knock and damage. Too late, and the engine loses power and runs hot. A knock sensor on many engines lets the ECM retard the timing if knock starts.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.