▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

The four-stroke cycle in detail – Garage Basics motor mechanics lesson

Lesson 1 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Follow one cylinder through intake, compression, power and exhaust, and work out how many power strokes an engine makes at a given speed.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The calculations use only division and multiplication. The cardboard model is the best way to see which valve is open on each stroke. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think engineers accept three "wasted" strokes in every four rather than designing an engine where every stroke is a power stroke?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking every stroke pushes the piston. Only the power stroke delivers work. The other three strokes use energy stored in the flywheel and from other cylinders.
  • Thinking the crankshaft turns once per cycle. Four strokes take two full turns, because each stroke is half a turn.
  • Thinking a diesel engine has spark plugs. A diesel relies on the heat of compression to ignite the fuel.

Hands-on: Make a model cylinder: cut a slot in a cardboard tube and slide a card "piston" up and down on a straw. Mark two paper flaps at the top as the inlet and exhaust valves. Move the piston through the four strokes, opening and closing the right flaps, while a partner calls out "intake, compression, power, exhaust". Count how many times a paper crank wheel joined to the straw must turn for one cycle.

What your child will learn

  • I can describe what the piston and both valves do in each of the four strokes.
  • I can explain why the crankshaft turns twice for every complete cycle.
  • I can calculate the number of power strokes per minute for an engine at a given rpm.
  • I can explain why engines with more cylinders run more smoothly.

Key words

stroke
One movement of the piston from the top of the cylinder to the bottom, or from the bottom to the top.
top dead centre (TDC)
The highest point the piston reaches in the cylinder.
bottom dead centre (BDC)
The lowest point the piston reaches in the cylinder.
inlet valve
The valve that opens to let the air and fuel mixture into the cylinder. In the US it is often called the intake valve.
exhaust valve
The valve that opens to let the burnt gases out of the cylinder.
crankshaft
The shaft that turns the up-and-down movement of the pistons into rotation.

The big ideas

Most petrol and diesel engines in cars are four-stroke engines. Inside each cylinder a piston moves up and down. Each movement from top to bottom, or bottom to top, is called a stroke. It takes four strokes – intake, compression, power and exhaust – to complete one cycle, and in that time the crankshaft turns round twice.

The US Department of Energy describes a petrol car's engine as spark-ignited: fuel is mixed with air and ignited by the spark plug. A diesel engine follows the same four strokes but has no spark plug; the fuel ignites because the air has been squeezed so hard that it is very hot.

Only one stroke in four – the power stroke – pushes the piston. The other three are driven by the momentum of a heavy flywheel and by the power strokes of other cylinders. That is why engines with more cylinders run more smoothly.

Read-through: the teaching steps

  1. 1 Intake

    The piston moves down from top dead centre. The inlet valve is open and the exhaust valve is closed. The falling piston lowers the pressure in the cylinder, and air (with fuel in a petrol engine) is drawn in. Follow the four drawings on the lesson page from left to right.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. 2 Compression

    Both valves close. The piston moves up and squeezes the mixture into a small space at the top of the cylinder. Squeezing a gas raises its pressure and temperature, which helps it burn quickly and powerfully.

  3. 3 Power

    Near the top of the compression stroke, a petrol engine's spark plug makes a spark (a diesel injects fuel into the hot air instead). The mixture burns rapidly, the hot gases expand and push the piston down hard. This is the only stroke that delivers work to the crankshaft.

  4. 4 Exhaust

    The exhaust valve opens and the piston moves back up, pushing the burnt gases out into the exhaust system. Then the exhaust valve closes, the inlet valve opens, and the cycle starts again.

  5. Two turns per cycle

    Each stroke is half a turn of the crankshaft. Four strokes = 4 × ½ = 2 turns. So a single cylinder makes one power stroke for every two turns of the crankshaft.

    • Power strokes per minute (one cylinder) = rpm ÷ 2
    • For several cylinders, multiply by the number of cylinders
  6. Smoothness and the flywheel

    A one-cylinder engine gets one push every two turns, so it runs roughly. A heavy flywheel on the crankshaft stores energy and keeps it turning between pushes. In a four-cylinder engine the power strokes are spaced out so there is one every half turn, which gives a much smoother flow of power.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.