▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Performance charts and safety factors (UK CAA 1.33 / 1.43 guidance) – Private Pilot Theory aviation lesson

Lesson 181 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

See how performance charts give unfactored distances and why the CAA recommends adding safety factors of 1.33 for take-off and 1.43 for landing.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why does it make sense to have a bigger safety factor for landing than for take-off?”
  4. Later: the homework, then the practice test.

Watch out for

  • Treating chart figures as achievable every time. They are unfactored – the CAA guidance adds 1.33 or 1.43.
  • Adding the safety factor as a percentage to other percentages. Multiply every factor.
  • Using 1.33 for landing. 1.33 is take-off; 1.43 is landing.

Hands-on: Find a page of a timetable or a table of numbers and practise interpolation: pick a value between two printed ones and work out the in-between figure.

What you will learn

  • I can name the main kinds of performance chart.
  • I can explain what "unfactored" data means.
  • I can apply the CAA 1.33 and 1.43 safety factors.
  • I can combine condition factors with the safety factor.
  • I can work out the shortest runway that the guidance would accept.

Key words

unfactored data
Chart figures achieved by test pilots in ideal conditions, with no safety margin.
safety factor
An extra multiplier for real-world variation: 1.33 take-off, 1.43 landing (CAA SafetySense 7c).
take-off distance chart
A table or graph of distance against conditions such as pressure altitude and temperature.
interpolation
Working out a value between two printed chart values.
factored distance
The chart distance multiplied by condition and safety factors.

The big ideas

The PHAK (chapter 11) lists the kinds of performance chart found in flight manuals: density altitude charts, take-off distance charts (tables or graphs, with wind and obstacle adjustments), climb charts (fuel, time and distance to climb), cruise charts, crosswind and headwind component charts, and landing charts. Values between printed figures are found by interpolation.

Chart figures are usually achieved by test pilots with new aircraft in ideal conditions. The CAA SafetySense Leaflet 7c therefore recommends an additional safety factor on unfactored data: 1.33 for take-off and 1.43 for landing, multiplied together with any condition factors (grass, slope, weight and so on). The leaflet stresses that factors must be multiplied.

So a chart take-off distance of 450 m becomes 450 × 1.33 = 598.5 m before any surface or slope factors. This is theory for understanding, not planning for a real flight.

Read-through: the teaching steps

  1. Kinds of chart

    • Density altitude
    • Take-off distance (with wind and obstacle adjustments)
    • Climb: fuel, time and distance
    • Cruise and range
    • Crosswind/headwind component
    • Landing
  2. Reading between the lines

    Interpolation: if 1,000 ft gives 400 m and 2,000 ft gives 440 m, then 1,500 ft – halfway – gives 420 m.

  3. Unfactored data

    Chart figures assume ideal conditions and skilled test pilots. Real-world variation – technique, tyre wear, runway – needs a margin.

  4. The CAA safety factors

    SafetySense 7c: multiply unfactored take-off distance by 1.33 and unfactored landing distance by 1.43.

  5. Combining everything

    Required distance = chart distance × condition factors × safety factor. Multiply all of them together.

  6. Shortest acceptable runway

    Turn it round: if the runway available is R, the largest chart distance it can accept is R ÷ (all the factors).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Flight Performance and Planning lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.